MECHANICAL: Enclosure: Rugged 18-gauge high-strength steel case. The case serves as a heat sink.Normally mounted vertically on a pedestal or metal surface along with PSX Power source.Metal mounting base included, 13-gauge steel (without the base, the box size is only 7”high). Mounting holes are a rectangle that is 3.35” X 7.92” (8.5 X 20.1cm) center-to- center. The lip at the bottom of the base can be used to anchor strain-relief for cables. Mounting screws (user supplied): Slot can accommodate sizes up to 1/4” diameter.Dimensions (wall mounted): OPERATING ENVIRONMENT: Ambient Temperature: rating of -40°C to 75°C long term per independent agency tests(UL), or -50°C to 100°C short term per IEC Type Tests. Cold start down to -20°C Storage temperature: -40° to 185°F (-40°to 85°C) Ambient Relative Humidity: 5% - 95% (non-condensing) Altitude: -200 to 50,000 ft. (-60 to 15,000m) UL2043 smoke tested for use in air handling spaces. mP62 and PSX units are IEC 529 rated IP51 (holds out dust, vertical water) Conformal coating (humidity protection) option, request quote. Operating Shock and Vibration: Meets Telcordia GR-63 Sections 4.4.1, 4.4.3 1.70 in D x 5.75 in W x 8.8 in H (4.3 cm x 14.6 cm x 22.4 cm)Weight of the unit: 3.5 lbs (1.6 Kg.) Cooling Method: Convection, with case operating as a heat sink

Specifications Specifications

Magnum mP62 and mP62-5VManaged Hardened Switch

Latency: less than 5 microseconds (not including packet time) Address Table size: 4K nodes, resets upon Link-loss on user-selected ports NETWORK STANDARDS: PERFORMANCE: Ethernet: IEEE 802.1p, 802.1d STP, 100BASE-TX, FX; IEEE 802.3, 10BASE-TAuto Negotiation (when ON): IEEE 802.3u, occurs at LINK enable All 10Mb ports obey the rules for 10Mb Ethernet, all 100Mb Fast Ethernet rules RJ-45 Ports: # 2-6 are 100 / 10Mbps, S/W control for speed and F/H duplex. Note – Crossover ( MDI vs. MDIX) is automatically handled on all RJ-45 ports. Fiber Ports : # 1 and 8 are 100Mb fiber, multi-mode or single-mode, S/W for F/HSwitching type: all ports non-blocking; S and F with IEEE 802.3x flow control. System aggregate forwarding and filtering rate: 1190K pps @ 100BASE-TX/FX Packet buffers: 256KB PDV: 50BT STANDARD SOFTWARE: SNMP, QoS, Telnet, Password Security, Port Settings Control, SpanningTree Protocol, port-based VLANs, BootP / DHCP, menu user interface LINK-LOSS-LEARN FEATURE A Link-Loss on user-designated ports immediately triggers new MAC addresslearning in the mP62 Switch address table, providing faster fault recovery LED INDICATORS: ( LEDs are viewed from the top surface) Power (on chassis): Steady on when power applied Per Port Speed: ON = 100Mb; OFF = 10Mb (with LINK On)Link/Act: Steady ON for LINK with no traffic, blinking for ActivityF/H: ON for full-duplex mode, OFF for half-duplex MANAGEMENT CONSOLE CABLE CONNECTOR: DB9 male, accepts industry standard null-modem cable.(software is installed or uploaded via a PC on the console port, or via TFTP). NETWORK CABLE CONNECTORS: Fiber: 100Mb mm SC, 100Mb Sgl-m SC-type 20km (other types via RFQ)RJ-45s with Auto-MDIX, 100Mb: Cat. 5 UTP/STP, 10 Mb: Cat. 3,4, 5 UTP Note Unique thermal techniques (patent pending) developed by GarrettCom tech-nologists extend the ambient temperature operating range beyond standard prod-uct ratings, and improve operating lifetime and reliability. POWER SUPPLY: Power Consumption: mP62 DC Power Input: 10 watts typical, 2A at 5VDC 20-70VDC auto-ranging, floating + and – screw terminals.Typically for use where 24VDC or –48VDC power is available. mP62-5V Power Input: 5VDC, screw-lock connector, typically for use withMagnum PSX-A or PSX-T Power Source, rated for 15 watts at -40°C to 75°C. Note: See PSX datasheet for details on AC, 125VDC and 250VDC power input

UL Listed (UL60950), cUL, CE, Emissions meet FCC Part 15, Class A. NEBS L3 and ETSI compliant IEEE 1613 Environmental Standard for Electric Power Substations. IEC61850 EMC and Operating Conditions Class C for Power SubstationsNEMA TS-2 and TEES for traffic control equipment. AGENCY APPROVALS AND STANDARDS COMPLIANCE:

MEAN TIME BETWEEN FAILURE (MTBF): 8+ years, Telcordia (Bellcore) Method. WARRANTY: Three years per Made in USA
ï›™ 2005 GarrettCom, Inc. Printed in United States of America Doc No. mP62 Rev7 2/05. GarrettCom, Inc. reservesthe right to change specifications, performance characteristics and/or model offerings without notice. GarrettCom, Magnum, Link-Loss-Learn (patent pending), and Personal Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc. NEBS is a registered trademark of Telcordia Technologies. UL is a registered trademark of Underwriters Labs.

Ordering Information

Magnum mP62-AC-1M1SSC

Magnum mP62-AC-2MSC

Same as mP62-AC-2MSC, except one fiber port is 20km single-mode SC. (includes PSX-A) mP62-AC Managed Ethernet Switch with six 10/100 RJ-45 and two 100Mb FDX fiber multi-mode SC-type ports. Software includes SNMP, QoS, Telnet, Security, STP, VLAN, BootP / DHCP. Has 4K nodes address table and 256KB packet buffers. AC power input, 85-260vac 47-63Hz worldwide auto-ranging, via PSX-A Power Source Extended Temp (a separate unit). Steel case used as a heat sink, designed for use in environmentally challenged locations such as extended temperature “outdoors.” Magnum mP62-AC-2SSC Same as mP62-AC-2MSC, except both fiber ports are 20km single-mode SC. (includes PSX-A) Magnum mP62-AC-NOF mP62-AC Ethernet Switch with six 10/100 RJ-45 and no fiber ports. Magnum mP62-2MSC mP62-DC Ethernet Switch, six 10/100 RJ-45 and two 100Mb FDX fiber multi-mode SC-type ports. Software and buffers same as mP62-AC-2MSC. DC power input, 20-70VDC auto- ranging. Magnum mP62-1M1SSC Same as mP62-2MSC, but with one multi-mode SC-type and one 20Km single-mode SC fiber connectors (No PSX unit required). Magnum mP62-2SSC Same as mP62-2MSC, except both 20Km single-mode SC fiber connectors (No PSX unit required). Magnum mP62-NOF mP62-DC Ethernet Switch with six 10/100 RJ-45 and no fiber ports Parts: Magnum mP62-5V-2MSC* Same as mP62-2MSC, except with 5VDC input using military-type screw-lock connector. Magnum mP62-5V-1M1SSC* Same as mP62-1M1SSC, except with 5VDC input using military-type screw-lock connector.

GarrettCom, Inc.

Magnum mP62-5V-2SSC* Same as mP62-2SSC, except with 5VDC input using military-type screw-lock connector.

213 Hammond Ave.Fremont, CA 94539PH: (510) 438-9071FAX: (510) 438-9072Email: mktg@garrettcom.comWeb: www.GarrettCom.com

Magnum mP62-5V-NOF Magnum PSX-5V-CBL (spare) Same as mP62-NOF, except w/ 5VDC input via PSX-A using military-type screw-lock connector. 2-ft power cord with military-type screw-lock connector, spare for PSX to mP62-5V power cord. MST Conversion Special Item, convert one standard mP62-2MSC w/ two MSC fiber ports to two MST fiber ports. * PSX unit or equal required to supply 5VDC input. For more information, please see the PSX datasheet. For Magnum mP62 and mP62-5V units with other fiber connector types, RFQ for additional information.