DC POWER SUPPLY OPTIONS:-48VDC: Input -36 to -70VDC 24VDC: Input 20 to 40VDC 125VDC: Input 88 to 150VDCStd. Terminal Block: "-, GND, +", Power Consumption: Same as AC DC DUAL POWER SOURCE (OPTIONAL) The Magnum 6K25 & 6K25R models may be ordered with optional Dual DC power input, for continuity of operation when either one of the DC input sources is interrupted. Available for -48VDC, 24VDC, or 125VDC. MECHANICAL: Enclosure: Rugged high-strength sheet metal. Suitable for stand- alone or 1U rack-mounting. Rack-mounting brackets: 19” included; ETSI and 23” Telco optional. Cooling Method: Fan cooled, internal @ 25cfm Dimensions: 1.70 in H x 17.0 in W x 9.0 in D 4.32 cm H x 43.2 cm W x 22.9 cm DWeight: rack-mount 5.0lbs. (2.0kg) LED INDICATORS PER RJ-45 PORT: LED INDICATORS, 100Mb and 10Mb FIBER PORTS: LK: Steady on when twisted-pair link is operational. ACT: On with port activity FDX/HDX: ON = full-duplex mode, OFF = half-duplex mode. 100/10 ON = 100Mb speed, OFF = 10Mb LK: Steady on when fiber link is operational. ACT: On with port activity, FDX/HDX PORT-SPECIFIC SETTINGS: The copper module has an internal switch for MDIX crossover on port #1. Other port-specific user settings (such as FDX or HDX, copper 10/100 speed) can be set using software commands. AGENCY APPROVALS: , NEMA TS-2 for traffic control UL Listed (UL1950), cUL, CE, Emissions meet FCC Part 15, Class A. NEBS L3 and ETSI Certified IEEE 1613 Environmental Standard for Electric Power SubstationsIEC61850 EMC and Operating Conditions Class C for Power Substations WARRANTY: Three years Made in USA

Specifications Specifications

Magnum 6K25 Managed Fiber Switch

PERFORMANCE:Gigabit Ports, 1000 Mb: Configurable, standard GBIC transceiver modules Fiber Fiber Ports, 10 Mb: RJ-45 Ports: 100 or 10 Mb Ports, 100 Mb Configurable, 4 ST ports per slot. Each port may be FDXor HDX, default is HDX mode (multi-mode and single-mode) speed, full- or half-duplex mode, per port,individually determined. 10/100 auto-negotiating and auto-cross : Configurable in modules,up to 24 ports total. Each FDX or HDX, default is FDX mode. All Ports non-blocking: RELAY CONTACT FOR ALARMS (OPTIONAL): µ s + packet time max (TX - TX, TX - FX, FX - FX, TX-G, G-G) Processing type: Store and Forward with IEEE 802.3x full-duplex flow controlSystem aggregate forward and filter rate 5.1Mpps (24ports @ 100Mb speed,1 port @ Gb) Address table: 4K nodes, self-learning, with address aging Packet buffers: 240 KB for 10/100 and 120KB for 1000 Mb Latency: 6 Form C, one NC indicating internal power, one NC software controllable. POWER SUPPLY (INTERNAL): NETWORK STANDARDS: OPERATING ENVIRONMENT: AC Power connector: IEC-type, male recessed, ON/OFF switch. Power Input Voltage: 100 - 240 VAC (auto ranging) Power Input Frequency: 47 to 63 Hz Power Consumption: 60 watts typical for a fully-loaded fiber model, 35 watts typical for copper-only models. IEEE 802.3z, 802.3ab, 802.1p: 100BASE-TX, -FX, 1000BASE-SX, -LX Auto-negotiation on TP, IEEE 802.3u See MNS-6K datasheet for software network standards, Link-Loss-Learn, and other soffware features UL 60950 “Component Parts” temperature rating: 130°F (55°C) IEC 60068 “Type Test” rating: -40° to 185°F (-40° to 85°C) Storage: -40° to 185°F (-40°to 85°C), Ambient relative humidity: 5% to 95% (non-condensing) Altitude: -200 to 13000ft (-60 to 4000m) Conformal coating (humidity protection) option: Request quote NETWORK CABLE CONNECTORS: 1000 Mb ports: all standard GBIC Transceiver types supported 100 Mb Copper: Category 5 UTP/STP; 10 Mb: Cat. 3,4, 5 UTP/STP 100 Mb Fiber ports connector options: multi-mode FX-MTRJ, LC, ST, SC; single-mode LC, 20Km SC, and 40Km "long reach" single-mode SC. 10 Mb Fiber port connector: multi-mode ST

ï›™ 2006 GarrettCom, Inc. Printed in United States of America Doc No. 6K25-R1 5 8 /06GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model offerings without notice. GarrettCom, Magnum, and Personal Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc. NEBS is a registered trademark of Telcordia Technologies. UL is a registered trademark of Underwriters Labs. Magnum 6K25

Ordering Information

Magnum 6K25 Managed Fiber Switch, base unit. May be configured with a selection of 10/100/1000Mb fiber and copper connector types, 25 ports max. Wire-speed filtering and forwarding across all ports, 802.3x flow control, 802.1p priority packet processing, self-learning 4K-node address table, and 240KB packet buffers. For licensed industrial management software, see applicable datasheet. Magnum 6K25R “Reverse” model, same as Model 6K25 except user ports and the power input connectors are in therear. Two sets of LEDs (both rear and front) provide duplicate status data for viewing from either side. Configuration Options: Each Magnum 6K25 and 6K25R base unit has four port module slots. Three (A, B, C) may be oneof the modules below, one (slot D) may only be a Gb module. Select up to 4 modules per base unit. 6KP8-45MT “4+4” module for 6Ks, w/four 10/100 RJ-45 and four 100 Mb 2km multi-mode FX MTRJ connectors 6KP8-SLC SFF Fiber module for 6K Switches, w/eight 100 Mb 15km single-mode FX LC connectors 6KP8-RJ45 TP Module for 6K 25 switches, w/eight 10/100 Mb auto-negotiating RJ-45 ports 6KP8-MTRJ SFF Fiber module for 6K Switches, w/eight 100 Mb 2km multi-mode FX MTRJ connectors 6KP8-45SLC “4+4” module for 6Ks, w/four 10/100 RJ-45 and four 100 Mb15km single-mode FX LC connectors 6KP6-RJMST “4+2” module for 6Ks, w/four 10/100 RJ-45 and two 100 Mb 2km multi-mode FX ST connectors 6KP6-RJSSC “4+2” module for 6Ks, w/four 10/100 RJ-45 and two 100 Mb 20km single-mode FX SC connectors 6KP6-RJSSCL “4+2” module for 6Ks, w/four 10/100 RJ-45 and two 100 Mb 40km single-mode FX SC connectors 6KP6-RJ10ST “4+2” module for 6Ks, w/four 10/100 RJ-45 and two 10 Mb 2km FL ST connectors 6KP4-FXSC “2+2” 100 Mb Fiber module for 6K Switches, w/four 100 Mb FX SC connectors. 6KP4-F10ST “2+2”10 Mb fiber module for 6K Switches, w/four 10Mb 2km FL ST connectors Note: Several other Port Module types are available. See Configuration Guide. 6KP5-G4RJ “G+4” module for 6K 25 Switches, uses, one 6K slot and provides one GBIC open transceiver portTransceiver module, plus 4 10/100Mb copper ports. Includes front-panel. 6KP3-G2SC “G+2” module for 6K 25 Switches, uses one 6K slot and provides one GBIC open transceiver port for a user-selectable GBIC Transceiver module, plus 2 100Mb 2km FX SC fiber ports. Includes front panel. GBPM-2OTX Two-port Gigabit 6K module for 6K 25 switches, provides two GBIC open transceiver ports. GBIC-SXSC GBIC transceiver module for use in GBPM-COTX, one SX port with multi-mode SC fiber connector

GarrettCom, Inc.

GBIC-LXSC10 GBIC transceiver module for use in GBPM-COTX, one LX port with single-mode SC 10Km

47823 Westinghouse DriveFremont, CA 94539PH: (510) 438-9071FAX: (510) 438-9072Email: mktg@garrettcom.comWeb: www.GarrettCom.com

Note: Single-mode GBICs are available at 10Km, 25Km, 40Km, and 70Km. 6KP2-2GSX 6KP2-2GCU Two-port one-slot Gigabit 6K module for 6K Two-port one-slot Gigabit 6K module for 6K 25 25 switches, uses one 6K slot and provides two Gigabit Copper (1000BASE-T) auto-negotiating ports. Includes front-panel sheet metal cover. switches, uses one 6K slot and provides two Gigabit Fiber SXSC (1000BASE-SX multi-mode) ports. Includes front-panel sheet metal cover. 6KP5-1CU4MT Five-port one-slot Gigabit 6K module for 6K 25 switches, uses one 6K slot and provides one Gigabit Copper (1000BASE-T) auto-negotiating port and four 100Mb MTRJ Fiber FX multi-mode ports. Includes front panel. 6KP3-1CU2FXT Three-port one-slot Gigabit 6K module for 6K 25 switches, uses one 6K slot and provides one Gigabit Copper (1000BASE-T) auto-negotiating port and two 100Mb ST Fiber FX multi-mode ports.