Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C
20Pages

{{requestButtons}}

Catalog excerpts

Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 1

Modular Chemical Process Pumps Technical Data Flow rate: Head: Speed: Materials: Temperature: Casing pressure: Shaft seal: Dimensions of flanges: Direction of: rotation max. 650 m³/h max. 150 m -1 max. 3600 min Cast iron, cast steel, stainless steel, hastelloy, duplex max. 350 ° C max. 25 bar Mechanical seal or magnetic coupling according to DIN or ANSI (see flanges) clockwise, when viewed from drive end Applications ISOchem Pumps of the SIHI range meet the requirements on custom-built solutions in the process industry, in the following areas: • Chemical • Pharmaceutical • Petro-chemical • Paper • Plastic • Food processing • Plant engineering and construction Hydraulic ISOchem The hydraulic of the SIHI is designed with closed impeller. Casing pressure PN16 and PN25. Maximal casing pressure = 25 bar. Max. casing pressure = inlet pressure + delivery head at zero flow. Please note The relevant technical regulations and safety rules must be observed. Flange location Axial suction flange, discharge flange radially upwards. Flanges According DIN EN 1092 or ANSI. Design ISOchem Chemical process pumps of the SIHI are horizontal, single-stage volute casing pumps with dimensions to DIN EN ISO 2858 and meet the technical requirements of DIN EN ISO 5199. It is a modular configuration of either bare shaft end or close-coupled design. Shaft sealing options are single or double-acting mechanical seals or magnetic couplings. The benefits are the interchangeability of the back pull-out assemblies and the reduction of spare parts cost. Materials Standard materials: Cast iron, cast steel, stainless steel, hastelloy, duplex. Special materials on request. Shaft sealing Mechanical seals: Magnetic coupling: - Single-acting seals - Double-acting seals - Cartridge seals - with or without heat barrier - Internal strainer - External partial flow - Heating jackets PUMP TECHNOLOGY SIHIISOchem 04/2013

Open the catalog to page 1
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 2

SIHIISOchem ISOchem Chemical process pumps in the range SIHI are horizontal, single-stage volute casing pumps with designs that fully meets technical requirements of DIN EN ISO 5199 and dimensions according DIN EN ISO 2858. This modular process pumps consists of hydraulics with closed impellers. Due to the modular configuration, the pumps can be used in a bare shaft or closecoupled configuration. Bare shaft design Close-coupled design Volute casing with closed impeller + Clean liquids + Low NPSH values CBS with single-acting mechanical seal and lifetime lubricated ball bearings CBE with...

Open the catalog to page 2
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 3

SIHIISOchem Execution with mechanical seal High efficiency Modern hydraulics High efficiencies Optimal velocities Condition monitoring High reliability Heavy duty thrust ball bearings / angular contact ball bearings Grease or oil lubrication Low installation cost Low NPSH value Optimised maintenance cost Lower shaft deflection than required by ISO 5199 Longer seal lifetime Longer lifetime of bearings High quality standard Labyrinth seal re-usable Shaft seal options Single or double-acting mechanical seal Cartridge seal Simple maintenance Back pull-out design Seal cover integrated in casing...

Open the catalog to page 3
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 4

SIHIISOchem Operating limits Temperature / Power Type Liquid handled according to characteristic curve 65 kW 90 kW * with thermal barrier up to 400 ° possible C Impeller material 1.4408, impeller material GG-25: nmax = 2900 min-1 Impeller material 1.4408, impeller material GG-25: nmax = 1800 min-1 Casing pressure Pressure - Temperature limits Casing material: Stainless steel, Hastelloy, Duplex Material desing: 4B, 4K, 4L, 4R, 5G, 5H, 5K, 5L perm. operating pressure [bar] perm. operating pressure [bar] Pressure - Temperature limits Casing material: Ductile iron, Cast steel Material design:...

Open the catalog to page 4
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 5

SIHIISOchem Shaft sealing Mechanical seal designs Single-acting mechanical seal Mechanical seal, type Cartridge Magnetic coupling designs Internal strainer External partial flow Heating jackets

Open the catalog to page 5
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 6

SIHIISOchem Sectional drawing and materials of construction Bare shaft end design with mechanical seal CBS with grease lubrication Design with external axial rotor adjustment Materials of construction CBS Materials 4B 4R Volute casing Casing cover Shaft sleeve Bearing house Mechanical seal various material combinations

Open the catalog to page 6
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 7

SIHIISOchem Sectional drawing and materials of construction Bare shaft end design with magnetic drive CBM up to 350 °C Volute casing Casing cover Sleeve bearing Bearing house Bearing insert Isolation shroud Inner magnet Outer magnet

Open the catalog to page 7
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 8

SIHIISOchem Sectional drawing and materials of construction Close-coupled design with magnetic drive CBE up to 350 ° (for 400 ° on request) C C Volute casing Casing cover Sleeve bearing Bearing insert Isolation shroud Inner magnet Outer magnet

Open the catalog to page 8
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 9

SIHIISOchem Table of dimensions Bare shaft end design with mechanical seal CBS bare shaft design to DIN EN ISO 2858 y = dimension for removal All dimensions in mm, tolerances to DIN EN 735 Size Pump dimensions Bearing bracket DNd DNS a f h1 Foot dimensions

Open the catalog to page 9
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 10

SIHIISOchem Table of dimensions Bare shaft end design with magnetic drive CBM ut : Connection for temperature sensor G1/4 uv : Connection for condition monitoring sensor SIHIdetect M8 x = dimension for removal All dimensions in mm, tolerances to DIN EN 735 Size Pump dimensions Bearing bracket DNd DNs a f h1 Foot dimensions

Open the catalog to page 10
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 11

SIHIISOchem Table of dimensions Close-coupled design with magnetic drive coupled CBE up to 350°C (for 400 °C on request request) ut : Connection for temperature sensor G1/4 uv : Connection for condition monitoring sensor S SIHIdetect M8 x = dimension for removal All dimensions in mm, tolerances to DIN EN 735 Size Motor size

Open the catalog to page 11
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 12

SIHIISOchem All dimensions in mm, tolerances to DIN EN 735 Size Motor size

Open the catalog to page 12
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 13

SIHIISOchem All dimensions in mm, tolerances to DIN EN 735 Size Motor size

Open the catalog to page 13
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 14

SIHIISOchem All dimensions in mm, tolerances to DIN EN 735 Size Motor size

Open the catalog to page 14
Series SIHIISOchem CBS/CBM/CBE, 650 m³/h, 150 m, 350 °C - 15

SIHIISOchem Flange dimensions Execution 1" on suction side (DN40) with 4 x threads ½” – 13 UNC All dimensions in mm, tolerances to EN 735 SG iron PN16 / PN25 Size Discharge nozzle Suction nozzle Discharge nozzle Suction nozzle Discharge nozzle Stainless steel ANSI 150 RF Suction nozzle Discharge nozzle Suction nozzle

Open the catalog to page 15

All Flowserve SIHI Pumps catalogs and technical brochures

  1. PL 325 M

    14 Pages

  2. LPG Solutions

    12 Pages