catalogue search
P. 01
P. 02
P. 03
P. 04
P. 05
P. 06
P. 07
P. 08
P. 09
P. 10
P. 11
P. 12
P. 13
P. 14
P. 15
P. 16
P. 17
P. 18
P. 19
P. 20
P. 21
P. 22
P. 23
P. 24
P. 25
P. 26
P. 27
P. 28
P. 29
P. 30
P. 31
P. 32
P. 33
P. 34
P. 35
P. 36
P. 37
P. 38
P. 39
P. 40
P. 41
P. 42
P. 43
P. 44
P. 45
P. 46
P. 47
P. 48
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You may also be interested in
Monorail conveyor, Guide, Management software, Software, Aluminum profile
Text version of the page
| - po Friction between chain and pallet In most cases, the coefficient of friction for contact between plain chain and pallet is between 0,1 and 0,35. | ||||||||||||||||||||||||||||||||||
| Temperature limits | xl | |||||||||||||||||||||||||||||||||
| xlp | ||||||||||||||||||||||||||||||||||
| ment temperatures from -20 °C to +60 °C. Temperatures up to +100 °C can be tolerated for short periods (cleaning, rinsing). x85 Maximum conveyor length X85P The maximum length of a conveyor depends on the tension in the chain, the speed, and the capacity of the drive xh unit. It is important to calculate and compare the maximum chain tension and the capacity of the drive unit in the fol- xk lowing situations: • Heavy load xkp • Accumulation | ||||||||||||||||||||||||||||||||||
| xb gr cs | ||||||||||||||||||||||||||||||||||
| • High speed • Long conveyor • Frequent starts and stops (high service factor). | ||||||||||||||||||||||||||||||||||
| Static electricity The standard plastic materials used for conveyors all have low electrical conductivity. This means that static | ||||||||||||||||||||||||||||||||||
| electricity can build up on the conveyor. If the chain runs | xc | |||||||||||||||||||||||||||||||||
| on plastic slide rails, no inherent discharge path exists for the static electricity. When a conveyor is running under normal operating xf conditions but without pallets, the following static build-up can be measured: | ||||||||||||||||||||||||||||||||||
| fst | ||||||||||||||||||||||||||||||||||
| At the drive unit.................................. 2000-2500 V At the idler end unit............................ 400-500 V At a wheel bend................................. 400-500 V xmy At a straight section............................ 300-400 V A pallet running on the conveyor can also build up static xlx electricity. The worst case is with accumulated pallets. Discharge is normally taking place when the pallets are transferred to or from the conveyor. In static sensitive xmx applications, a number of measures can be taken to reduce the risk of excessive static charges. qrx 1 Ensure that the relative humidity is minimum 40%. | ||||||||||||||||||||||||||||||||||
| PQY | ||||||||||||||||||||||||||||||||||
| 2 Install static discharge wipers immediately before sensitive points on the conveyor. | ||||||||||||||||||||||||||||||||||
| Components for static sensitive environments Some FlexLink chains and slide rail can be ordered in carbon loaded versions. The carbon loaded material has high conductivity. Contact your FlexLink Systems representative for additional information. | ||||||||||||||||||||||||||||||||||
| © FlexLink- | ||||||||||||||||||||||||||||||||||
| 221 | ||||||||||||||||||||||||||||||||||
| Technical information | ||||||||||||||||||||||||||||||||||