SRS Series Safety Cable Pull Switch
9Pages

{{requestButtons}}

Catalog excerpts

SRS Series Safety Cable Pull Switch - 1

Monitoring Devices For Conveyor System

Open the catalog to page 1
SRS Series Safety Cable Pull Switch - 2

FOR PROTECTION OF BELT CONVEYORS AND PERSONNEL FEATURES Switching Capacity This device monitors the operation process for potentially hazardous conditions and activate an alarm when it is occurred misalignment, the SRT series conveyor belt misalignment switch protects the conveyor belt from damage due to belt misalignment or run off ° For normal condition, the belt misalignment switches are generally mounted on both sides and the edge of the conveyor belt ° A small clearance between the contact rollers and a little swaying for the belt edges are allowable. When the swaying exceeds the...

Open the catalog to page 2
SRS Series Safety Cable Pull Switch - 3

FOR EMERGENCY OR NORMAL SHUT-OFF SRS Belt conveyor safety cable pull switches are designed for providing a switching system to isolate the power to conveyor system and other equivalent process equipment in the emergency condition ° The cable pull switches are actuated by a plastic coated steel wire, which are placed along-side the conveyor ° When you pull on the cable at any point, it will trip and automatically lock the switches, deenergizing the conveyor starter contactor ° Each switch is bi-directional in operation and has two cable fitted to it from opposite directions terminated with a...

Open the catalog to page 3
SRS Series Safety Cable Pull Switch - 4

ED4000 ED4000(SM4) Speed Monitor is a totally new rotational speed monitoring equipment; it uses the principle of photo detector and microprocessor to accurately calculate a wide range of rotational speed. It detects rang 1~999rpm and the rotational speed display on 7-seg led. There is a contact relay that could be used either for alarm or control purposes during the monitoring process. The alarm set point could be directly set by numerical knobs which is more convenient and more accurate than conventional means. It comes equipped with analog signal output which could be utilized for...

Open the catalog to page 4
SRS Series Safety Cable Pull Switch - 5

DESCRIPTION OF OPERATION Q Set point rotary switch (2 Power & Alarm indicator (Green/Red) © Start Up Delay Selection Switch <3 4-20mA output range Selection Switch d 7 Segment display 1 .Set point rotary switch The function of this switch is for setting alarm position. The rotary switch consists of 3 buttons, including x100, x10 and x1. If the setting is at 321rpm, then rotate the SW4 to position 3, rotate the SW3 to position 2 and rotate the SW2 to 1. 2.Alarm indicator (Red)/Power indicator (Green) 1. When the monitor detects the speed lower than the setting point and reach to the alarm...

Open the catalog to page 5
SRS Series Safety Cable Pull Switch - 6

WORKING PRINCIPLE Working power supply Shortest reserved space EDX10 is a brand new speed monitoring device exclusively designed for a belt conveyor, which monitors the rotation speed by using the optoelectronic switch or magnetic induction part. During this process, it provides an output contact SPDT for alarm or control. The alarm setting is determined by the scale on the adjustment knob, which is convenient and fast. Based on the conventional analog design, it uses a simple, stable and low-cost circuit, which makes it economical. • The alarm point setting of the speed monitor adopts a...

Open the catalog to page 6
SRS Series Safety Cable Pull Switch - 7

PANEL CONFIGURATION DIAGRAM Status indicator Speed setting knob Startup alarm delay switch Power supply input Relay output INSTALLATION INSTRUCTION Contact type Tap the 3/8“ ( or M10) screw hole in a central towards the axis direction of the driven wheel on the device to be monitored; fasten the copper connector on the rotation axis with the screw. And then set up a scaffold in front of the reversed rotation axis, align the axis center of the speed monitor and the driven wheel, and then fix it. Finally, connect with the rubber bellow and fasten the metal straps to finish the installation....

Open the catalog to page 7
SRS Series Safety Cable Pull Switch - 8

0: Contact type 1: Non-contact type Working power supply A: 110/220Vac, 50/60Hz B: 24Vdc Output type- R: Single relay output, 5A/250Vac

Open the catalog to page 8
SRS Series Safety Cable Pull Switch - 9

■ Asia ® Taiwan FineTek Co., Ltd. - Taipei Head Quarter No.16, Tzuchiang St., Tucheng Industrial Park New Taipei City 236, Taiwan TEL: 886-2-2269-6789 FAX: 886-2-2268-6682 EMAIL: info@fine-tek.com ■ North America ® California, U.S. Aplus Finetek Sensor Inc. - US Office 355 S. Lemon Ave, Suite D, Walnut, CA 91789 TEL: 1 909 598 2488 FAX: 1 909 598 3188 EMAIL: info@aplusfine.com ■ Europe <§> Germany FineTeK GmbH - Germany Office Frankfurter Str. 62, OG D-65428 Ruesselsheim, Germany TEL: +49-(0)61 42-1 7608-0 FAX: +49-(0)61 42-1 7608-20 EMAIL: info@fine-tek.de ® Illinois, U.S. Aplus Finetek...

Open the catalog to page 9

All FineTek Co. catalogs and technical brochures

  1. Thermocouple

    12 Pages