Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch
9Pages

{{requestButtons}}

Catalog excerpts

Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch - 1

Monitoring Devices For Conveyor System visit our website

Open the catalog to page 1
Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch - 2

CONVEYOR BELT MISALIGNMENT SWITCH FOR PROTECTION OF BELT CONVEYORS AND PERSONNEL This device monitors the operation process for potentially hazardous conditions and activate an alarm when it is occurred misalignment, the SRT series conveyor belt misalignment switch protects the conveyor belt from damage due to belt For normal condition, the belt misalignment switches are generally mounted on both sides and the edge of the conveyor belt ° A small clearance between the contact rollers and a little swaying for the belt edges are allowable. When the swaying exceeds the normal limit (on/ about...

Open the catalog to page 2
Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch - 3

SAFETY CABLE PULL SWITCH FOR EMERGENCY OR NORMAL SHUT-OFF Belt conveyor safety cable pull switches are designed for providing a switching system to isolate the power to conveyor system and other equivalent process equipment in the emergency The cable pull switches are actuated by a plastic coated steel wire, which are placed along-side the conveyor ° When you pull on the cable at any point, it will trip and automatically lock the switches, deenergizing the conveyor starter contactor ° Each switch is bi-directional in operation and has two cable fitted to it from opposite directions...

Open the catalog to page 3
Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch - 4

SPEED MONITOR ED4000(SM4) Speed Monitor is a totally new rotational speed monitoring equipment; it uses the principle of photo detector and microprocessor to accurately calculate a wide range of rotational speed. It detects rang 1~999rpm and the rotational There is a contact relay that could be used either for alarm or control purposes during the monitoring process. The alarm set point could be directly set by numerical knobs which is more convenient and more accurate than conventional means. It comes equipped with analog signal output which could be utilized for various display indications...

Open the catalog to page 4
Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch - 5

DESCRIPTION OF PANEL DESCRIPTION OF OPERATION 1 2 Power & Alarm indicator (Green/Red) 3 Start Up Delay Selection Switch 4 4-20mA output range Selection Switch 5 1.Set point rotary switch The function of this switch is for setting alarm position. The rotary switch consists of 3 buttons, including x100, x10 and x1. If the setting is at 321rpm, then rotate the SW4 to position 3, rotate the SW3 to position 2 and rotate the SW2 to 1. Set point rotary switch 7 Segment display 1 5 8 0 1 8 6 4 3 7 SW4 5 6 SW5 9 2 5 3 4 4 8 1 1 9 0 1 6 7 4 5 5 4 3 3 SW3 2 8 5 5 2 7 0 7 7 9 1 3 3 0 2 2 9 4 3 2.Alarm...

Open the catalog to page 5
Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch - 6

MULTI-FUNCTION TEMPERATURE AND SPEED SAFETY METER Multi-function temperature and speed safety meter is designed to detect and surveillance bearing temperature and pulley speed of conveyor and hopper type lifter. It offers functions as alarm and shut-down signaling under unusual condition, and measuring recording. Users will have better knowledge in equipment condition and degree of depreciation, which enriches field workers safety ■ Easy installation and operation. ■ Key pad lock with password to avoid unexpected ■ 4 sets of bearing temperature and 1 set of pulley speed detection. ■ Auto...

Open the catalog to page 6
Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch - 8

DISPLAY PANEL DESCRIPTION Alarm Indicator General Switch Speed Value Upper Bearing Lower Bearing Power Communication Indicator Indicator Shut down Indicator Status Indicator Speed Indicator Temperature unit

Open the catalog to page 8
Speed Monitor/Convery Belt Misalignment Switch/Safety Cable Pull Switch - 9

EXAMPLES OF TANK MOUNTINfi [FC/FD] Mini Float/Magnetic Float Level Switch [FG] Magnetic Float Level Transmitter [FF] Side Mounting Float Switch [FA/FB] Cable Float Level Switch [SP] Thermal Dispersion Flow Switch [SF] Paddle Flow Switch [SD] Optical Level Switch [SE] Rotary Paddle Level Switch [SA] Capacitance Level Switch [EC] Pressure Level Transmitter [LR] Loop Power Indicator [SC] Vibrating Probe Level Switch [SC] Tuning Fork Level Switch [EB] RF-Capacitance Level Transmitter [SB] RF-Capacitance / Admittance Level Switch [EG] Magnetostrictive Level Transmitter [EF] By-Pass Level...

Open the catalog to page 9

All FineTek Co. catalogs and technical brochures

  1. Thermocouple

    12 Pages