ST50
6Pages

{{requestButtons}}

Catalog excerpts

ST50 - 1

FCI ST50 Series Flow Meters Low Cost, Low Maintenance Air, Compressed Air and Nitrogen Flow Measurement for Process and Plant Applications Wastewater Treatment Aeration Control Blower and Dryer Air Flow Control Burner and Furnace Air Flow Control Lake, Pond and Aquaculture Aeration HVAC Duct/Damper Control Compressed Air Distribution Measurements

Open the catalog to page 1
ST50 - 2

FCI ST50 Series Flow Meters Easy to Install, Easy to Use The ST50 Flow Meter is an accurate, easy to install, no moving parts solution for measuring and controlling air, compressed air or nitrogen flow. ST50 utilizes FCI proven thermal dispersion technology to provide direct mass flow measurement resulting in higher performance at a lower cost than orifice plates, DP, Vortex shedding and other thermal devices. The meter installs in line sizes ranging from 2 inches to 24 inches [51 mm to 610 mm] with 1/2 ″ or 3/4 ″ NPT. ST50 uses precision, lithography structured platinum RTD sensors...

Open the catalog to page 2
ST50 - 3

Exclusive “Wireless” Communications Option With FCI’s unique new IR link option, any Palm-OS based PDA can be used to communicate with the ST50 without contact. This wireless IR link features a password protected, easy-to-follow menu driven program to access all its features. Parameters include measured readings and totalizer values, configuration settings, calibration downloads, diagnostic service codes, and more. This wireless interface is ideal to save cost and time when the ST50 will be mounted in a hard to reach location. Requires FCI software accessory kit P/N 019819-01 for the PDA....

Open the catalog to page 3
ST50 - 4

Media Compatibility: Air, compressed air, and nitrogen Pipe/Line Size Compatibility: 2" to 24" [51 mm to 610 mm] Range: Air, compressed air, or nitrogen: 0.75 SFPS to 400 SFPS Accuracy: Standard: ± 2% of reading, ± 0.5% of full scale Optional: ± 1% of reading, ± 0.5% of full scale Temperature Compensation: FM/CSA: Nonincendive for use in Class 1, Division 2, Hazardous (Classified) Locations. (DC input power only) Flow Element Installation: Insertion, variable length with 1/2" or 3/4" MNPT compression fitting Type: Thermal dispersion Material of Construction: 316 stainless steel body with...

Open the catalog to page 4
ST50 - 5

ST50 Flow Meter Single Insertion Point, Mass Flow Measurement With premium components and attention to detail FCI’s ST50 series provides long-lasting flow meter quality and value. It’s features and functions ensure application compatibility, maximum installation convenience, superior industrial durability and lowest maintenance. Analog and digital outputs Dual conduit ports, NPT or M20, facilitate power and signal wire run isolation and access Easy access to all wiring terminations with removable front and rear covers Compact, rugged, NEMA 4X (IP67), all metal enclosure and agency approvals...

Open the catalog to page 5
ST50 - 6

Companion FCI Flow Meters in the ST50/ST75 Series ST75 Flow Meter Series Insertion style flow meter similar to Model ST50 for biogas, digester gas and other methane composition gases, also with enhanced features for air applications. In-line (spool-piece) version for applications with smaller line sizes, 1/4″ to 2″ [6 to 51mm] and for all air and gases. – Two-line, Flow Rate + Totalizer Digital Display – Agency Approvals for Div.1/Zone 1 Installations – For all air and gases including hydrocarbons and hydrogen – Pulse Output for External Totalizers is standard – Two-line, Flow Rate +...

Open the catalog to page 6

All FCI Fluid Components International catalogs and technical brochures

  1. ST100

    20 Pages

  2. ST75

    9 Pages

  3. ST51

    2 Pages

  4. MT series

    8 Pages

  5. GF90

    6 Pages

  6. FLT

    8 Pages

  7. FCI

    12 Pages

Archived catalogs