Catalogues - taps-dies-catalog

Catalogue Taps & Dies Catalog

www.fastcut.com

Page

/ 58

Contact the
Manufacturer

Where to buy
this product ?

/ 58

See other catalogues for Fastcut Tool

Text version of the page

HIGH SPEED STEEL / GROUND THREAD

These general purpose taps can be used by hand or under power, in through or blind holes and are suitable for tapping most materials. The chips are retained in the flutes during use. Three-fluted taps have the greatest chip holding capacity and should be used, in the size range where available, for tapping holes deeper than 1-1/2 diameters. A variety of surface treatments are available to improve performance. See Page 49 for recommendations. See Table 302 on Page 33 for tap dimensions.

LIST 102


	NC NF				EDP NO.
SIZE	NS	H-mvnT	FLUTES	TAPER	PLUG	BOTTOM	SET
0-80	NF	H1	2	10000	10001	10002	10003
0-80	NF	H2	2		10005	10006
1-64	NC	H1	2	10008	10009	10010	10011
1-64	NC	H2	2		10013
1-72	NF	H1	2	10016	10017	10018	10019
1-72	NF	H2	2		10021	10022
2-56	NC	H1	3	10028	10029	10030	10031
2-56	NC	H2	2		10033	10034
2-56	NC	H2	3	10036	10037	10038	10039
2-64	NF	H2	3	10044	10045	10046	10047
3-48	NC	H1	3		10049
3-48	NC	H2	2		10053	10054
3-48	NC	H2	3	10056	10057	10058	10059
3-56	NF	H2	3	10060	10061	10062	10063
4-40	NC	H1	2		10065
4-40	NC	H1	3	10068	10069	10070	10071
4-40	NC	H2	2		10073	10074
4-40	NC	H2	3	10076	10077	10078	10079
4-48	NF	H1	3		10081
4-48	NF	H2	3	10084	10085	10086	10087
4-36	NS	H2	3	10088	10089	10090	10091
5-40	NC	H1	3		10093	10094
5-40	NC	H2	2		10097	10098
5-40	NC	H2	3	10100	10101	10102	10103
5-44	NF	H2	2		10105
5-44	NF	H2	3	10108	10109	10110	10111
6-32	NC	H1	2		10113
6-32	NC	H1	3	10116	10117	10118	10119
6-32	NC	H2	2		10121	10122
6-32	NC	H2	3	10124	10125	10126	10127
6-32	NC	H3	2		10129	10130
6-32	NC	H3	3	10132	10133	10134	10135
6-32	NC	H7	3		10137	10138
6-40	NF	H1	3		10141
6-40	NF	H2	2		10145
6-40	NF	H2	3	10148	10149	10150	10151
8-32	NC	H1	2		10153
8-32	NC	H1	3		10157	10158
8-32	NC	H1	4	10160	10161	10162	10163
8-32	NC	H2	2		10165	10166

Machine Screw High Speed Steel

THREAD FORM

American National

CHAMFER STYLE

Taper (7 to 10 threads), Plug (3 to 5 threads), Bottoming (1 to 2 threads) If chamfer style is not specified, plug will be furnished

continued

FASTCUTTOOL