catalogue search
P. 01
P. 02
P. 03
P. 04
P. 05
P. 06
P. 07
P. 08
P. 09
P. 10
P. 11
P. 12
P. 13
P. 14
P. 15
P. 16
P. 17
P. 18
P. 19
P. 20
P. 21
P. 22
P. 23
P. 24
P. 25
P. 26
P. 27
P. 28
P. 29
P. 30
P. 31
P. 32
P. 33
P. 34
P. 35
P. 36
P. 37
P. 38
P. 39
P. 40
P. 41
P. 42
P. 43
P. 44
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You may also be interested in
Band heater, Digital controller, Controller, Tubular heater, Strip heater
Text version of the page
| Pulse™ Series Control Instruction Manual | |||||||||||||||||||||
| Column 1 (Top): PARAMETER/SCREEN "Parameter or Screen to be Secured" This column represents the parameter or screen that can be locked out in security. The parameters are as follows: | |||||||||||||||||||||
| SECTION REFERENCE ABOUT..................................10 System Operation....................10 RUN........................................10 STOP........................................10 BOOST....................................10 IDLE ........................................11 Navigate/Change Values..........11 Pulse Screens............................12 Help ........................................14 Main Screen ............................15 Zone Main Setup......................18 Zone Limits Setup....................21 Zone Boost/Idle Setup..............25 Zone PID Setup........................28 System Setup Screen................31 File System ..............................34 Security....................................35 Security Setup..........................36 Alarm......................................38 Printing....................................40 | |||||||||||||||||||||
| Lockout on temperature and power setpoint for Boost under BOOST setup. Lockout on temperature and power setpoint for Idle under IDLE setup. Lockout on temperature setpoint on all screens indicating "SET" when in automatic mode. Lockout on manual power setpoint on all screens indicating "SET" when in manual mode. Lockout from Zone mode on all screens indicating "MODE". Lockout on Slave To on MAIN screen. Lockout from access to Zone setup screen. Lockout from access to Setup Limits screen. Lockout from access to PID setup screen. Lockout from access to System setup screen. Lockout from access to File Select screen. Lockout from access to Print Reports screen. Lockout from access to Alarm Acknowledge screen. | |||||||||||||||||||||
| BOOST SETPOINTS | |||||||||||||||||||||
| IDLE SETPOINTS TEMPERATURE SETPOINTS MANUAL POWER SETPOINTS ZONE MODE SLAVE TO SETUP ZONE SCREEN SETUP LIMITS SCREEN SETUP PID SCREEN SETUP SYSTEM SCREEN FILE SELECT SCREEN PRINT REPORTS SCREEN ALARM ACKNOWLEDGE | |||||||||||||||||||||
| Column 1 (Bottom): SECURITY CODES Selection: 0001 to 9999 Description: Under each of the three levels there is the ability to give four separate security codes for each level. | |||||||||||||||||||||
| Column 2: L1 "Level 1 Access" Selection: ON = Security lockout enabled; OFF = Security lockout disabled. Description: This is typically setup as the lowest level access for security. It is recommended that if security is used that this be setup with no access to the setup screens. | |||||||||||||||||||||
| Column 3: L2 "Level 2 Access" Selection: ON = Security lockout enabled; OFF = Security lockout disabled. Description: This is the secondary level access for security, typically recommended for setup personnel. | |||||||||||||||||||||
| Column 4: L3 "Level 3 Access" Selection: ON = Security lockout enabled; OFF = Security lockout disabled. Description: This is the highest level of security. It is recommended that all the parameters be left "ON" for this level of security. | |||||||||||||||||||||
| ALARM | |||||||||||||||||||||
| 37 | |||||||||||||||||||||