Text version of the page

Completing Step 3 of the Model Number

General shock notes: 1) Shocks not available on EZ250 model.2)Shocks not available on EZ375-MF3 3)1/2” –20 thread shocks/brackets are used on EZ375, EZ500 & EZ625.4)1”–12 thread shocks/brackets are used on EZ750, EZ1000 & EZ1500. â–¼

Shock Option Details

The Step 3 chart on the opposite page indicates whatshocks are available for each tooling option. • Indicate shock quantity/location in the box ( ) as follows:

Adjustable Stop Option Details

E = Extend only; R = Retract only; B = Both ext. & retract.Some shock options do not require a tooling option (EZ375models, or "retract shock only"). Fill in Tooling/Stop optionposition with zeros if shocks are desired without toolingoptions. Example: EZ375-6.0-MH1-S000- The Step 3 chart on the opposite page indicates what stopsare available for each tooling option. A tooling option must beselected before a stop option can be specified.
0000BB

Code 00 –

â–¼

This code indicates no stops desired.

â–¼

Code NO –

Indicates no shocks

Code 01 –

Flange Nuts Standard Shock Location
Allows complete adjustment overthe entire stroke length from full tozero stroke. Threaded rod (with two flange nuts serving as the stops) isfastened to cylinder endcap andpasses thru a clearance hole in reartooling. STD. RETRACT DUAL SHOCK LOCATION STD. EXTENDSHOCKSTD. RETRACT SHOCKLOCATIONSHOCK DOGATTACHED TO GUIDE SHAFT STD. EXTENDDUAL SHOCK Stroke repeatability within .001” â–¼

Code U1 –

Urethane Washers Standard Location Alternate Location A .............. Ace Shocks.................... D
Reduces noise and provides an impact absorbing stop cushion.It is the same stop as Type “01” with a urethane washer slippedonto the threaded rod against theflange nut. B ........... Enidine Shocks.................. E C ....Brackets & Actuators only.......... F
(Customer supplies the shocks) Advantage: Quiet operation Insert E, R or B in box
Note: Stopping accuracy is limited toapproximately ± .025” because of thecompressibility of the washer Alternate Shock Location

Linear Slides Catalog - 11741 âžš

(Recommended whenusing “BL, CS, PL, PS, or VB” Tooling)

âžš

â–¼

Code 02 –

. Is a modification of Type “01” where a stop bolt is added forthe extend stop. It positions bothextend and retract adjustmentsnext to each other at the backof the slide.Provides easier, more accessibleadjustment in cases where a toolingoption would cover the extendflange nut in a Type “01” stop ALTERNATE RETRACT SHOCK LOCATION STD. EXTENDSHOCKSTD. EXTENDDUAL SHOCK Stop Bolt ALTERNATE RETRACT DUAL SHOCK LOCATION Stop Plate Stroke repeatability within .001” Note : EZ1500 models with Type “01” stop are available with aDual Shock Option (2 extend and/or 2 retract shocks). SensorsS01 thru S60, when used with dual shocks are re-located. Both sensors are mounted to the front end cap. .

Code 03 –

Can only be used with “BL”, “CS”, “PL”, “PS”, or “VB” tooling options.Uses stop bolts at each end. Onapplications where the front & reartall blocks are fixed and the cylinderis a reciprocating carriage, this “03”option eliminates the threaded stoprod which otherwise would also be reciprocating and require special guarding. PROX. SWITCH DOG DUAL PROX. BRACKET DUAL SNAP SWITCHES Standard Location Alternate Location AX ............. Ace Shocks.................. DX
Stop Plates Stop BoltStop Bolt BX .......... Enidine Shocks............... EX
Stroke repeatability within .001” CX ...Brackets & Actuators only.......

âžš âžš

FX
(Customer supplies the shocks) Insert E, R or B in box
1-20-99 Specifications subject to change without notice or incurring obligations Page 51