Filter- Regulator - Lubricators Catalog
66Pages

Pancaked Cylinders originai &"r series Section 11ndex Detailed Specification Model Number Codes Standard Dimensions Seal Kit Part Numbers Magnetic Piston Position Sensing Option Dimensions Flow Controls Specifications subject to change without notice or incurring obligation

Pancake® Cylinders Original & “T” Series 8 Bores, 1/2" – 4" Features & Benefits This, the original Pancake® Cylinder, was designed in 1958 to satisfy the need for short stroke cylinders that would fit in very tight spaces. Today, with almost four decades of experience in thousands of cylinder applications around the world, The Pancake® Line offers you far more than any of its imitators – more features and options – better quality, strength and appearance – and far longer product life! We are so confident in our design and manufacturing skills that we back every Pancake® Cylinder with our...

Pancaked Cylinders originai & T series Construction Details ^^^^^^^^^^^^^M 8 Bores, 1/2" - 4" ^^^^^^^^^^^^^^M Nearly 4 decades of experience paying close attention to design detail, production and assembly techniques have resulted in the ultimate Fabco-Air Pancake®, short stroke cylinders. Pancakes® fit into very tight spaces and virtually ANY short stroke cylinder application. Think how well they will fit with your application! 1. The heavy wall prohibits any damage to the bore from external 2. The one piece cylinder body and bushing support end is machined from solid aluminum bar-stock....

Pancake® Cylinders originai & T series Action Information Original Series PTFE Piston Bearing Action Letter Action Description Double Acting Power Extend - Power Retract Double Acting Power Extend - Power Retract Piston guide pins for nonrotating Single Acting - Spring Retracted Power Extend - Spring Retract Single Acting - Spring Extended Spring Extend - Power Retract Specifications subject to change without notice or incurring obligation

Pancake® Cylinders Action Information The "Action Letter" portion of the Pancake® Model Number specifies how many piston rods the cylinder has (Single Rod or Double Rod), how the piston rod is extended and retracted (Double Acting or Single Acting), and if the piston rod is restricted from rotating by internal guide pins (Nonrotating). Original Series PTFE Piston Bearing Action Letter Action Description Double Acting Two Piston Rods - One each end Power Extend - Power Retract Action -XDRK Double Acting Two Piston Rods - One each end Power Extend - Power Retract Piston guide pins for...

Pancake® Cylinders Option Information PREFIX OPTIONS MODEL NUMBER PREFIX METRIC Cylinder and Rod Thread. M Female Rod Thread is standard. Optional Male Rod Thread PREFIX OPTIONS Mounting holes and rod thread are configured to common METRIC sizes. Ports in 1/2" (5) and 3/4" (7) bores are M5. Ports in 1-1/8" (121) bore and larger are G1/8 with 14mm spotface for 1/8 BSP-Parallel Available on all series, bore, stroke and action combinations. See Option Specifications pages of desired bore and action for complete dimensional details. Specifications subject to change without notice or incurring...

Pancake® Cylinders Option information SUFFIX OPTIONS MODEL NUMBER SUFFIX Double Rod, Both Ends SUFFIX OPTIONS A high strength stud is threaded into the standard female rod end and retained with Loctite®. This method eliminates the small diameter thread relief area normally required when machining male threads. This provides a much stronger rod end which can be repaired, rather than replacing the complete rod, should the thread be damaged. Available on all series, bore, stroke and action combinations. See Option Specifications pages of desired bore and action for complete dimensional...

Pancake® Cylinders Construction Details SUFFIX OPTIONS MODEL NUMBER SUFFIX HYDRAULIC, Low Pressure Service Consult factory for media compatability and operating temperatures over 300°F. With Standard Thickness With Thick Cover SUFFIX OPTIONS For Air-Oil or Hydraulic systems to 500 psi NONSHOCK. 1. A specially formulated U-Cup seal replaces the O-ring piston rod seal. This eliminates leakage past the rod seal and around the bushing. 2. Option-HHC, on single rod bores 1-5/8" (221) & larger, includes a thicker rear cover to assure that there is no warpage or failure when the mounting surface...

Pancake® Cylinders Option information SUFFIX OPTIONS HOLE THRU Double Rod Shaft SUFFIX OPTIONS 150 psi maximum operating pressure A hole is drilled through the piston rods & the double rod stud (see construction details on page 1.3). This hole is used for the passage of Vac- uum, Air, Gas, Oil, Liquid or any media that is compatible with the stainless steel piston rod and the steel stud. Maximum pressure, 150 psi. Hole sizes available for each bore size are shown in the chart to the left. If a larger hole is needed (for higher flows or mechanical members) or all stainless steel construction...

Pancake® Cylinders Option information SUFFIX OPTIONS MODEL NUMBER SUFFIX ADJUSTABLE EXTEND STROKE Full stroke adjustment is standard. NOTE! Use caution when mounting to avoid creating pinch poiunts. Adjustment settings are simplified by convenient scale markings ap- plied to nut skirt and stop tube. SUFFIX OPTIONS Dial-A-Stroke® provides a rugged and precision adjustment of the extend stroke of the cylinder. The stop tube, adjustment nut with skirt & minimum clearances combine to eliminate pinch points, thus providing operator safety. Note! Use caution when mounting to avoid creating pinch...

Pancake® Cylinders Option Information SUFFIX OPTIONS MODEL NUMBER SUFFIX SOUND LIMITERS SUFFIX OPTIONS For applications where you need a small amount of cushion at the end of the cylinder stroke to take out the metallic "slap" of piston head on piston stop. This is accomplished by placing an O'Ring on the piston, and/or in the rear cover so that initial contact is with the elastomer The Fabco-Air design assures sufficient compression of the seals to allow full stroke. Because of the temperature limitations of the adhesives involved, sound limiters are available in cylinders with internally...