clamping solutions
32Pages

F-Tool clamping solution FT 00348 - Version 06.15 / English Innovat i ve Tooling S olutions

F-Tool ZeroPoint Clamping System (ZPS) simple palletising with the F-Tool PowerFlex Centring Wonderfully simple... Patent Pending F-Tool ZPS The F-Tool ZPS is a simple, precise, powerful zero point clamping system. The positioning takes place by means of conically cut clamping pins which compress the centring ring during clamping and form a friction-locked connection with the base unit. This compensates for any lateral clearance. The pallet can be fastened to the ZPS base unit mechanically using screws or by means of an additional independent clamping mechanism. F-Tool ZPS-300-36-M - For...

F-Tool ZeroPoint Clamping System (ZPS) Universal In the F-Tool ZPS the four PowerFlex centring units automatically form a reference position in the centre of the base unit. The reference position is not as normally determined by a centring unit, but equalised evenly by means of the four PowerFlex centring rings. Minor deviations in the positioning on the pallet or thermal influence are systematically compensated and centrically distributed by the PowerFlex centring rings Pallet 300 x 300 mm Clamping holes for M12 base plate Integrated reference position Integrated straight edge Fastening...

F-Tool ZeroPoint Clamping System (ZPS)Operated manually or automaticallyF-Tool ZPS Duo-Compact 280 MTS with F-Tool PowerFlex centring The F-Tool ZPS duo compact with PowerFlex centring is a precise, economic and powerful zero point clamping system. The F-Tool PowerFlex centring takes place by means of conically cut clamping pins which compress the centring ring during clamping and form a friction-locked connection with the base unit. The F-Tool ZPS duo basic unit can be aligned on the machine coordinates by the centre of the chuck and the integrated alignment rail, with no additional aid....

Application with ZPS pallet 300 x 300 mm compatible with F-Tool PowerPlate and EROWA MTS pallets P148 various aluminium and steel plates 300 x 300mm are available for daily use

F-Tool ZeroPoint Clamping SystemF-Tool ZPS Duo Compact 280 MTS-A The circuit of the Z-support of the ZPS duo basic unit gives an optimal stability and prevents the entry of washing liquid, dirt and chips at the same time. The relative big Z-support causes a good contact with the pallet, what affects the vibration attitude of the machine and the tool wear especially positive at milling performance. Furthermore the Z-supports of the alu pallets do not have to be forced additionally. Material: Burnished steel Positioning exactness: ± 0,005 mm Air supply: 1/8" open MTS chuck 7 bar 1/8"...

F-Tool ZeroPoint Clamping System F-Tool ZPS-300-55-MP-MTS single base unit pneumatic The pneumatic ZPS base unit is suitable for the use on milling centres with 5 axes. The ZPS base unit excels thanks to the simple inexpensive construction. The central MTS clamping chuck can also be used as a central single unit with F-Tool PowerPlate or EROWA P pallets 148 mm or only as a clamping mechanism for ZPS pallets. In case of high loads the pallet 300 x 300mm can be additionally secured using 4x M12 screws. The ZPS base unit can be aligned at the front on the reference surface and put in centrally...

ets for ZPS 300 F-Tool ZPS ALU pallet M 300 x 300 x 44mm The ZPS aluminium pallet is milled parallel and prepared with clearance bore hole for the central MTS clamping chuck. The pallet is equipped with four PowerFlex centring bolts (FT 02164). The milled in handles facilitate the handling. The pallet is prepared with 8 fastening holes for M12 screws. Other bore holes can be added separately, if necessary. The four lateral M8 holes can be used with screws for the crane or the additional handle FT 02175. Assembly examples

ZPS pallet ALU 300/44 mm IF FT-CentroClamp-180 1/2 The F-Tool pallet ALU 300/44 (FT 02165) is prepared with a hole pattern to accommodate one or two CentroClamp 180UP, FT 02063/ FT 02064. The ZPS aluminium pallet is milled parallel and prepared with clearance bore holes for the central MTS clamping chuck. The pallet is equipped with four PowerFlex centring bolts. Supplied without MTS clamping spigots. The clamping bolt FT 02173 is required for clamping with the central MTS clamping chuck. Assembly examples F-Tool ZPS pallet ALU 300/44mm blank central clamper 130 x 55 mm 1/4 The F-Tool...

MTS clamping spigot A 1 item clamping spigot without centring (centring clearance 0.1 mm), incl. fastening screws (M10 x 50 x 55), u-disc, O-ring and protection caps. For the use of the pallet 300 x 300 mm on the base unit with central MTS clamping chuck. F-Tool ER-PowerPlate Centering plate with P-profile, compatible with FT 01043 F-Tool ER chuck 80P plus all EROWA chucks with P-profile, EROWA PowerChuck and EROWA ProductionChuck 210 Combi. Highly friction centering. For the direct assembling on pallets and fixtures. Clamping spigot F/M long without rinsing Model: type, fixed, manual....

Strong design Convincing technology Excellent value - Cast frame incl. integral guides - Reduced height - Prepared for PowerPlate and direct assembling on pallets and T-slot tables - FT 02281 F-Tool plus more grip clamping jaw with special tooth grip. The clamping jaw is suitable for roughing and finishing. * with grip profile

- Repeatability: ± 0.01 mm - Clamping range depending on clamping jaw 0 - 180 mm - Adjustable zero point - Grid dimension of jaw regulation: 12 mm - Compact and robust construction F-Tool CentroClamp 180UP F-Tool CentroClamp 180UP - Maximum clamping power: 18 kN - Maximum clamping force: 80 Nm - Clamping path: 0 - 44 mm - Exchangeable clamping jaws - Strong spindle with acme thread TR 26 x 3 mm F-Tool jaws and accessories Mounting FT 01835 PowerPlate 4 x M8 for additional supporting feet 0 4 x M8 for mounting from bellow o 6 x 010.5 for mounting from upside 0 2 x positioning bolt PP 06 mm

F-Tool Blank CentroClamp F-Tool Blank CentroClamp 130 x 96 x 55 mm The F-Tool blank CentroClamp is above all suitable to process aluminium and steel parts with 5 axes. The F-Tool blank central clamper has a compact structure and covers clamping dimensions of 10 - 80mm. Supplied with 7° tilted screws clamping jaws. The blank central clamper can be mounted from behind with 4 x M8/110 x 50mm and 4 x M8 Tk37 mm. The centre provides of a bore hole dm12h7mm for the positioning. Clamping width: 90 mm Clamping area: 10 - 80 mm Dimension: l = 130 mm x 90 mm, h = 55 mm Suitable to clamp parts with a...