Welding Consumables Handbook - 505 / 529 Pages

General information

Table 1. Hardfacing and cladding. Choose the right OK electrode for different working conditions ENVIRONMENT Resistance-Suitability

5. Superior, 3. Good, 1. Limited usability

CORROSIVE ENVIRONMENT

5. OK 92.26, OK 92.35, OK 92.86, OK 94.25, OK 94.55, OK 93.01, OK 93.12 Requirements:Corrosion resistance 4. OK 68.81, OK 68.82, OK 67.45, OK 67.52 3. OK 84.80, OK 84.78, OK 84.42, OK 84.52 2. OK 84.58, OK 83.50 1. OK 83.28, OK 83.65, OK 85.58, OK 85.65, OK 86.08 >

HIGH TEMPERATURE Oxidizing

5. OK 92.26, OK 92.35, OK 93.01 Requirements:Scaling resistance 4. OK 68.81, OK 68.82, OK 84.78, OK 67.45, OK 83.65, OK 84.80 3. OK 84.42, OK 84.52, OK 84.58, OK 85.58, OK 85.65 2. OK 83.50, OK 92.86 1. OK 83.28, OK 86.08, OK 86.28 >

Annealing, Softening

5. OK 92.35, OK 93.01, OK 93.12 Requirements:Hardness at high temperature, annealing resistance 4. OK 84.78, OK 85.58, OK 85.65 3. OK 84.42, OK 84.52, OK 84.58, OK 83.50, OK 83.65 2. OK 83.28, OK 86.08, OK 86.28, OK 68.81, OK 68.82 1. OK 67.45, OK 67.52 >

LOW TEMPERATURE

5. OK 92.26, OK 92.35, OK 92.86, OK 67.45, OK 94.25, OK 94.55 Requirements:Cold toughness 4. OK 67.52, OK 86.28, OK 86.08 3. OK 83.28, OK 68.81, OK 68.82 2. OK 83.50, OK 84.42, OK 84.52 1. OK 83.65, OK 84.58, OK 84.78, OK 85.65, OK 93.01 >

TYPE OF WEAR Impact, high surface pressure

5. OK 92.35, OK 86.08, OK 86.28, OK 68.81, OK 68.82, OK 93.07 Requirements:Impact-resistance and resistance to crushing 4. OK 67.45, OK 67.52, OK 83.28 3. OK 92.25, OK 93.06 2. OK 84.42, OK 84.52, OK 85.65, OK 93.12 1. OK 83.50, OK 83.65, OK 84.58, OK 84.78, OK 94.25, OK 94.55, OK 93.01 >

Wear by blast stone and ore

5. OK 84.78, OK 84.84, OK 84.80, OK 93.01 Requirements:
High surface-hardness or
cold-work hardening weld metal 4. OK 86.08, OK 86.28, OK 83.65, OK 85.65, OK 93.12 3. OK 83.50, OK 84.58, OK 84.42, OK 84.52, OK 93.06 2. OK 85.58, OK 68.81, OK 68.82, OK 67.45, OK 67.52, OK 93.07 1. OK 83.28 >

Wear by fine grained materials

5. OK 84.84, OK 84.78, OK 84.80, OK 93.01 Sand and clay Requirements:
High surface hardness 4. OK 83.65, OK 85.65, OK 93.12 3. OK 84.58, OK 83.50, OK 93.06 2. OK 84.42, OK 84.52, OK 68.81, OK 68.82, OK 85.38 1. OK 67.45, OK 67.52, OK 83.28, OK 86.08, OK 86.28, OK 93.07 >

Cavitation

5. OK 63.35, OK 67.71, OK 93.06, OK 93.07 4. OK 67.45, OK 67.52, OK 94.55, OK 94.25 3. OK 84.42 2. OK 84.52, OK 84.58, OK 93.01, OK 93.12 1. OK 83.28 >

505

Welding Consumables Handbook
  1. P. 1

  2. P. 500

    General information Handwelding electrodes Official approval >In addition to the official approval given in this catalogue, many OK electrodes are...
  3. P. 501

    General information Choice of suitable electrode The OK electrodes in this catalogue are placed into groups according to the type of alloy deposit-ed....
  4. P. 502

    General information Unalloyed basic electrodes Rutile-basic, high-efficiency electrodes Unalloyed basic electrodes give moderate weld-ing speed in the...
  5. P. 503

    General information Choose the correct OK electrodes, wires and fluxes for hardfacing and maintenance. Recommendations for the right choice of electro-des...
  6. P. 504

    General information Choose the right OK Electrodes for joining dissimilar materials1. OK 67.70, OK 67.752. OK 67.45, OK 68.81, OK 68.82Fig. 11. OK 92.262....
  7. P. 505

  8. P. 506

    General information Recommended post weld treatment Stress relief Stress relief Stress relief Stress relief Stress relief Consumables for MAG, MIG, FCAW,...
  9. P. 507

    General information Recommended post weld treatment Stress relief Stress relief Hammering Consumables for MAG, MIG, FCAW, SAW OK Tubrodur 14.71 OK Tubrodur...
  10. P. 508

    General information Recommended post weld treatment Tempering 550C Tempering 625аC Tempering 625C Stress relief, 500аC Stress relief, 500C...
  11. P. 509

    General information General recommendations GMAW GMAW Gas Metal Arc Welding The electrodes and joint faces should be clean. This is particularly important...
  12. P. 510

    General information General recommendations for Submerged Arc Welding 1. The flux must be dry . Agglomerated fluxes must be protected from moisture pick-up....
  13. P. 520

Text version

All ESAB catalogues and technical brochures

  1. RT250 ? RT500

    2 Pages

    En
  2. Column & Boom

    2 Pages

    En
  3. AGW1 and AGW2

    2 Pages

    En
  4. BEVEL EXCAVATOR

    5 Pages

    En
  5. Oxy-fuel torches

    9 Pages

    En
  6. ESAB Plasma VBA

    3 Pages

    En
  7. VISION? T5

    5 Pages

    En
  8. ALPHAREX

    4 Pages

    En
  9. SUPRAREX TM HD

    9 Pages

    En
  10. COMBIREX? DX

    7 Pages

    En
  11. E-VENT?

    7 Pages

    En
  12. Miggytrac 1001

    2 Pages

    En
  13. A21 PRB and PRC

    2 Pages

    En
  14. DATA LEAP

    7 Pages

    En
  15. COLOMBUS III

    5 Pages

    En
  16. Wind Power

    1 Pages

    En
  17. Buddy Arc 145

    2 Pages

    En
  18. Buddy Tig 160

    2 Pages

    En
  19. PT26

    2 Pages

    En
  20. PowerCut 900

    2 Pages

    En
  21. PowerCut 700

    2 Pages

    En
  22. PowerCut 400

    2 Pages

    En
  23. PowerCut 1600

    2 Pages

    En
  24. Buddy? Arc 180

    2 Pages

    En
  25. KHM 351 YS

    2 Pages

    En
  26. TIGAID 315 AC/DC

    2 Pages

    En
  27. Kit F-15-691

    2 Pages

    En
  28. 20519 RP

    16 Pages

    En
  29. Chart ver-b

    1 Pages

    En
  30. 20Data.

    182 Pages

    En
  31. 20201

    46 Pages

    En
  32. 20450

    74 Pages

    En
  33. 20360

    46 Pages

    En
  34. CC-11

    44 Pages

    En
  35. SSP-10000

    36 Pages

    En
  36. SSP-1014

    4 Pages

    En
  37. SWR-10002

    2 Pages

    En
  38. SWR-10000

    14 Pages

    En
  39. COR-1049B

    22 Pages

    En
  40. COR-1055

    16 Pages

    En
  41. COR-1078

    21 Pages

    En
  42. COR-1076

    9 Pages

    En
  43. SWR-10001

    6 Pages

    En
  44. ALC-10001

    4 Pages

    En
  45. Remote controls

    2 Pages

    En
  46. Caddy™Arc251i

    2 Pages

    En
  47. TIGAID 315 AC/DC

    2 Pages

    En
  48. WeldPoint™

    2 Pages

    En
  49. QSet™

    1 Pages

    En
  50. PSF™ Centrovac

    2 Pages

    En
  51. PSF™

    2 Pages

    En
  52. MXL™ Torches

    2 Pages

    En
  53. Aristo™U8 / W8

    2 Pages

    En
  54. MMA

    2 Pages

    En
  55. TIG

    2 Pages

    En
  56. MIG/MAG compacts

    2 Pages

    En
  57. Suprarex SXE BIG

    9 Pages

    En
  58. ESP 150 Plasma

    6 Pages

    En
  59. Pulsed MIG Welding

    20 Pages

    En
  60. NewTech Helmets

    4 Pages

    En
  61. A2 Multitrac SAW

    2 Pages

    En
  62. wire feed unit

    2 Pages

    En
  63. Product Catalogue

    105 Pages

    En