Heavy-Edged Metallized Polypropylene - Electrocube - #1

Text version of the page

DRILL SERIES [Europe].indd table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:4.00pt "Arial", sans-serif; } .font1 { font:5.00pt "Arial", sans-serif; } .font2 { font:7.00pt "Arial", sans-serif; } .font3 { font:8.00pt "Arial", sans-serif; } .font4 { font:9.00pt "Arial", sans-serif; } .font5 { font:10.00pt "Arial", sans-serif; } .font6 { font:14.00pt "Arial", sans-serif; } .font7 { font:15.00pt "Arial", sans-serif; } .font8 { font:11.00pt "Arial Black", sans-serif; } .font9 { font:9.00pt "Palatino Linotype", serif; } .font10 { font:7.00pt "Tahoma", sans-serif; } .font11 { font:5.00pt "Verdana", sans-serif; } .font12 { font:9.00pt "Verdana", sans-serif; } ^electrocube high current/high frequency metallized polypropylene 945 series The new rugged Séries 945 metallized capacitors offer high frequency opera­tion, high current and low ESR in a miniature package. They are able to handle high surge currents without degrading thus making them an excellent electrolytic capacitor replace­ment. Series 945 are ideal for audio systems. This capacitor series was designed for AC and pulsing appli­cations. The units are rated for 67 VRMS and 100 and 270 VRMS (to 100 KHz), but may also be used for all DC applications up to 200 VDC and 400 VDC respectively. Units are available in axial-lead wrap and fill, in oval and round shapes, and in voltages of 100, 200, 400 and 600 VDC. All capacitors feature extended foil construction and standard tin-coated copper leads. Protective clear wrap is offered on all wrap and fill units. The potting material and endfills of Electrocube's capacitors meet or exceed the flammability requirements of UL94VO. Dimensional variations for all MFD values are available with the same volume to meet your design requirements. SPECIFICATIONS TYPICAL DIELECTRIC CHARACTERISTIC CURVES Température: -55°C to +85°C at rated voltage; to +105°C with 50% voltage derating. Dielectric Voltage Test: Will withstand the application of 150 VDC, 300 VDC, 600 VDC and 900 VDC on 67 VAC, 135 VAC, 270 VAC and 440 VAC, respectively at 25° C for a period not to exceed 1 minute; current limited to 5 mA. DC Life Tests: Will withstand the application of 138 VDC, 280 VDC, 560 VDC and 840 VDC, respectively, on the 67 VRMS, 135 VRMS, 270 VRMS and 440 VRMS parts at 105°C for 250 hrs., with not more than 1 failure in in 12 permitted, current limited to 5 mA. LU a z < o CAPACITANCE VS. TEMPERATURE LU O Z < O < o For life test détails, contact the factory. Dissipation Factor: Shall not exceed 0.1% at 25°C for values to 1 mfd; 0.2% for values 1 mfd and over Dielectric Absorption: Shall not exceed 0.1% at 25°C per MIL-C-19978. Acceptance Criteria: Measurement frequency for capacitance and dissipation factor shall be 1000 Hz for values up to 1 mfd and 120 Hz for values of 1 mfd and over. NOTES: For information regarding insulating sleeves, mountings, special terminals, non-standard leads, circuit connections and other hardware, please consult factory. For styles and ratings not shown, or for unusual requirements necessitated by special circuit applications (including Dr O i— O Ll z g en en □ TEMPERATURE l°C: INSULATION RESISTANCE VS. TEMPERATURE Ll_ 5 LU O Z < O < o TEMPERATURE (°C) TYPICAL ESR VALUES — 945 SERIES higher IR or lower DF), consult the factory direct NOTES: Derate Amp 30% ® 50°C. J ' Current ratings based on component ambient temperature of 25° C. All Electrocube film capacitors have endfills and tape that meet or exceed the flammability requirements of UL94V0. 30 40 50 60 70 80 10C ESR — MILLIOHMS 3366 Pomona Blvd. • Pomona, CA 91768 • TEL: (909) 595-4037 • FAX: (909) 595-0186 GIGCTrOCUDG e-mail: esales@electrocube.com • Internet: www.electrocube.com • (IR: 9/99)