Catalogue G-Code programming manual
www.delectron.it
print switch display
Page / 149
D.Electron - 3262, 3548, 87114, 208480
/ 149
See other catalogues for D.Electron
Text version of the page
CNC Z32 - Programming guide (Milling machines)
6.1.9 G800K9: Three zones drilling...............................................................................................................71
6.1.10 G800K10: Internal spiral milling-boring...............................................................................................72
6.1.11 G800K11: External spiral milling-boring.............................................................................................72
6.2 Z32 positioning macros (G801)..................................................................................................................73
6.2.1 G801K1: Line - starting point and increments...................................................................................75
6.2.2 G801K2: Line - starting point, angle and point distance..................................................................75
6.2.3 G801K3: Line - starting and end point................................................................................................75
6.2.4 G801K4: Grid - row and column increments.....................................................................................76
6.2.5 G801K5: Grid - starting point, distances and angles.......................................................................76
6.2.6 G801K6: Grid - row and column starting and end points................................................................76
6.2.7 G801K7: Circle - initial angle and total increment............................................................................77
6.2.8 G801K8: Circle - initial angle and angular distance.........................................................................77
6.2.9 G801K9: Circle - initial and final angle...............................................................................................78
6.2.10 G801K10: Rectangle - center and pitch.............................................................................................78
6.2.11 G801K11: Rectangle - center and sides............................................................................................78
6.2.12 G801K12: Rectangle - corner and pitch............................................................................................79
6.2.13 G801K13: Rectangle - corner and sides............................................................................................79
6.3 Z32 machining macros (G802)....................................................................................................................80
6.3.1 G802K1: Circular pockets roughing....................................................................................................82
6.3.2 G802K2: Rectangular pocket roughing - pocket center..................................................................83
6.3.3 G802K3: Rectangular pocket roughing - corner................................................................................84
6.3.4 G802K4: Circular pockets finishing.....................................................................................................85
6.3.5 G802K5: Rectangular pocket finishing - pocket center...................................................................86
6.3.6 G802K6: Rectangular pocket finishing - corner.................................................................................87
6.3.7 G802K7: Linear eyelet...........................................................................................................................88
6.3.8 G802K8: Circular eyelet - eyelet center.............................................................................................89
6.3.9 G802K9: Circular eyelet - curvature center.......................................................................................90
6.3.10 G802K10: Hole thread milling with a single flute end mill................................................................91
6.3.11 G802K11: Hole thread milling with a comb end mill.........................................................................92
6.3.12 G802K12: Stud thread milling with a single flute end mill................................................................93
6.3.13 G802K13: Stud thread milling with a comb end mill.........................................................................94
6.3.14 G802K14: Face milling..........................................................................................................................95
6.4 Machine tool builder's fixed cycles (G27C..)........................................................................................96
7. PROFILES ON THE PLANE..............................................................................................................................97
7.1 Closed lines..................................................................................................................................................99
7.1.1 Line - end point (G1 X.. ; G1 Y.. ; G1 X.. Y..)....................................................................................99
7.1.2 Line - end coordinate and slope (G1 X..QF.. ; G1 Y..QF..).............................................................99
7.1.3 Line - two coordinates end point and slope (G1 X.. Y.. QF..).......................................................100
7.2 Open lines (G1;G1QF..)...........................................................................................................................101
7.3 Closed circles............................................................................................................................................102
7.3.1 Circle - center and end point (G2/G3 I.J..X..Y..)............................................................................102
7.3.2 Circle - end point and radius (G2/G3 X..Y..RA..)............................................................................103
7.3.3 Circle - center, radius and end slope (G2/G3 I..J..RA..QF..)........................................................104
7.3.4 Circle - center and end slope (G2/G3 I..J..QF..).............................................................................104
7.3.5 Circle - radius and end slope (G2/G3 RA..QF..).............................................................................105
7.3.6 Circle - end point (G2/G3 X..Y..).......................................................................................................106
7.3.7 Circle - center and end arc length (G2/G3 I..J..QA..).....................................................................106
7.4 Open circles................................................................................................................................................107
7.4.1 Circle - center and radius (G2/G3 I.J..RA..)...................................................................................107
7.4.2 Circle - center (G2/G3 I..J..)...............................................................................................................108
7.4.3 Circle - radius (G2/G3 RA..)...............................................................................................................108
7.5 Line-circle combinations.......................................................................................................................... 109
7.6 Automatic fillets (RR..)............................................................................................................................111
7.7 Chamfers......................................................................................................................................................115
8. DISK FILES RECALL.......................................................................................................................................116
8.1 Machining of files generated by CAD-CAM systems.........................................................................116
iii
DirectIndustry's Virtual Technical Library: PDF Catalogue | Technical Documentation | Brochure | Manual | Industrial directory | Specifications | Characteristics
Search Go
page 1 p.1
page 2 p.2
page 3 p.3
page 4 p.4
page 5 p.5
page 6 p.6
page 7 p.7
page 8 p.8
page 9 p.9
page 10 p.10
page 11 p.11
page 12 p.12
page 13 p.13
page 14 p.14
page 15 p.15
page 16 p.16
page 17 p.17
page 18 p.18
page 19 p.19
page 20 p.20
page 21 p.21
page 22 p.22
page 23 p.23
page 24 p.24
page 25 p.25
page 26 p.26
page 27 p.27
page 28 p.28
page 29 p.29
page 30 p.30
page 31 p.31
page 32 p.32
page 33 p.33
page 34 p.34
page 35 p.35
page 36 p.36
page 37 p.37
page 38 p.38
page 39 p.39
page 40 p.40
page 41 p.41
page 42 p.42
page 43 p.43
page 44 p.44
page 45 p.45
page 46 p.46
page 47 p.47
page 48 p.48
page 49 p.49
page 50 p.50
Pages:
1-50
51-100
101-149