Receiver D2001K - DATEK - (Version JPG) - Page n° 2 - PDF Catalogue | Technical Documentation



Comprehensive safety Datek uses synchronous data transmission, which means that each bit of data is checked very carefully. Even the smallest deviation from the norm is detected, and then the entire data packet that has been received is rejected. Each system has a unique ID code. If the transmitter's ID code does not match the receiver's, radio communication will never be established. Both the protocol and its checksum are digitally verified by dual processors using different software. This provides what is known as a redundancy check. If the processors interpret the protocol differently, they immediately shut down all outputs. Such safety features as digitally verified transmission and redundancy checking are just two of the innovations which Datek has pioneered in the area of radio remote control. Since it's founding in 1979 Datek has focused on developing safe radio remote controls, something we still do and will continue to do. Feedback The receivers in this series can be provided with two-way communication. Feedback to the transmitter unit is obtained through semi-duplex, which means that only one frequency is utilised for both control signals to the receiver and feedback data. This is advantageous if availability of frequencies is limited, as you are only taking up one frequency instead of two.			The receiver series is available in four different versions The D2001K can control up to 20 digital functions. The receiver is suitable for applications with one, two or more speed steps. The D2001KL can control up to four motions proportionally along with nine digital functions. The four analogue outputs are galvanically separated and are fitted with directional and, if required, full-speed relays. The D2001KM can control up to 14 digital functions. This receiver is more compact (220 x 120 x 90 mm) than the other receivers in this series and is therefore suitable for installation in confined spaces. The receiver enclosure is made of sturdy fibreglass, which complies with protection class IP65. The D2001K PLC has parallel PNP outputs or serial communication via RS-232 for PLC control. The receiver is supplied as standard on a mounting plate with terminal strips to be fitted into a control cabinet together with a PLC. As an option, the receiver can also be supplied in a steel or stainless-steel cabinet. Options • Signal horn • Pre-assembled machine cable with Harting connector • Extension cable for aerial • Stainless-steel cabinet Recommended transmitters D2801 MIDI D2801 MIDI Extended D2012 Hand-Held Transmitter

Dimensions Output relays Proportional outputs Digital outputs Digital inputs Digital / analogue inputs Serial output Frequency Temperature range Protection class Supply voltage	2001K 300 x 200 x 160 mm 8A/250 VDC	2001KL 2001KM 300 x 200 x 160 mm 220 x 120 x 90 mm 8A/250 VDC 8A/250 VDC 4 pes 0 - 10 VDC / +/-10 VDC / 4 - 20 mA - 9 14			2001K/PLC 280 x 250 x 70 mm
	20 8				28 (PNP) ⁶ 8 RS232 406 - 472 MHz -25° - 70°C IP20 12 - 36 VDC
	20 8	8		8
	406 - 472 MHz -25° - 70°C IP65 12 - 36 VDC / 48, 110, 230 VAC	406 - 472 MHz -25° - 70°C IP65 24 - 36 VDC / 48, 1 10, 230 VAC		406 - 472 MHz -25° - 70°C IP65 12 - 36 VDC

Further information For more information about our radio systems, please visit our website at www.datek.net or call us on +46 8 534 101 50. We will be glad to help you.

Datek AB Box 94 147 22 TumbaSweden Drottningvagen 13 147 31 TumbaSweden Phone +46 8 534 101 50_Fax +46 8 530 341 60_www.datek.net				a datek

Receiver D2001K - DATEK - #2

Receiver, Joystick, Transmitter, Radio remote control, Remote control