Catalog excerpts
SHEET 8-Port Skorpion Gigabit Switch Cost Effective, High-speed — Compact Size The EISK8-GT Skorpion Gigabit Switch is an 8-port unmanaged Ethernet switch that provides Gigabit Ethernet (GigE) performance on all ports in order to accommodate high-speed devices such as IP cameras and modern workstations. In addition, GigE jumbo frames up to 9216 bytes are supported for the highest possible system performance. For 10/100 Mbps legacy devices, the switch will automatically reduce its port-speed accordingly, thereby accommodating the needs of just about any Ethernet automation system. This low-cost compact unit utilizes a rugged metal enclosure and is intended for installation in control panels using DIN-rail mounting. This is a plug-and-play Ethernet switch requiring no configuration. All ports automatically configure their data rate and duplex using the Auto-negotiation protocol. Depending on the capability of the link partner, communication is set at 10, 100 or 1000 Mbps and at either half- or full-duplex. Each port will accommodate either a straight-through or crossover cable by using the Auto-MDIX protocol. The unit is powered from a choice of low-voltages (AC or DC). Redundant power connections are provided for back-up power schemes. LED indicators assist in troubleshooting network issues. • Plug-and-Play operation • DIN-rail mounting • Rugged metal enclosure • Diagnostic LEDs • Auto-negotiation of speed and duplex • Auto-MDIX supports cable inversion • UL 508 listed, c-UL listed, CE mark • 24 VAC/VDC powered
Open the catalog to page 1Overview The Skorpion Gigabit Switch is intended for control panel installations where DIN-rail space is at a premium by requiring a width of only 41 mm of rail space. A metal DIN-rail clip attached to the aluminium enclosure can survive the toughest installation. A writable side label allows the installer an opportunity to document field cabling locations right on the unit. connections, a backup power scheme can be supported. A removable power connector facilitates the servicing of the unit. The switch can powered from either a 10–36 VDC or 24 VAC (±10%) source. Its half-wave rectified...
Open the catalog to page 2Specifications Power Requirements Operating Temperature Storage Temperature Relative Humidity Shipping Weight Ethernet Communications IEEE 802.3 10/100/1000 Mbps data rate using RJ-45 connectors, 100 m (max) Supports jumbo frames up to 9216 bytes Power “H” LEDs “L” LEDs “H” or “L” LEDs Regulatory Compliance Green = power OK Green = 1000 Mbps communication established Yellow = 100 Mbps communication established Yellow = 10 Mbps communication established Flashing = data transmissions occurring CE Mark; CFR 47, Part 15 Class A; RoHS; UL 508 Industrial Control Equipment Mechanical Drawing
Open the catalog to page 3Power Considerations Applied voltage must be in the specified range and deliver a current commensurate with power consumption. The recommended size for solid power conductors is 16-20 AWG; and for stranded conductors use 16-18 AWG. Zero volts (COM) is isolated from chassis (earth). Input connections are reverse-polarity protected. Connecting chassis to earth or using a backup source is always optional. All options shown are for use in Class 2 circuits if applied voltage is limited to 30V DC. Typical Switch Installation AC Powered with AC Powered with Redundant DC Grounded Secondary DC...
Open the catalog to page 4All Contemporary Control Systems catalogs and technical brochures
-
DS-PC104220B
4 Pages
-
DS-AISRVR00B
6 Pages
-
TD9905200D
3 Pages
-
TD9905000D
3 Pages
-
TD0209000D
3 Pages
-
DS-EIS00000B
4 Pages
-
DS-EISK8PG0B
4 Pages
-
DS-EISK5000B
4 Pages
-
DS-EISK5GH0B
4 Pages
-
DS-EISK5G00B
4 Pages
-
EXTEND-A-BUS Series
6 Pages
-
CANPCI Series
3 Pages
-
CAN104-DN
3 Pages
-
CANISA
3 Pages
-
BASgateway
4 Pages
-
Portable BASrouter
8 Pages
-
BASrouter
8 Pages
-
BASview
16 Pages
-
BAScontrol
8 Pages
-
BASremote
8 Pages
-
CTRLink®
6 Pages
Archived catalogs
-
ARCNET for Control
86 Pages