Catalog excerpts
SHEET 5-Port Skorpion Switch Cost Effective, 100 Mbps-speed — Compact Size The EISK5-100T Skorpion Switch is a five-port unmanaged and duplex using the Auto-Negotiation protocol. Depending Ethernet switch that provides 100 Mbps performance on all on the capability of the link partner, communication is set at ports in order to accommodate a range of control devices 10 or 100 Mbps and at either half- or full-duplex. Each port and workstations commonly found in an automation project. will accommodate either a straight-through or crossover For 10 Mbps legacy devices, the switch will automatically cable by using the Auto-MDIX protocol. reduce its port-speed accordingly. This low-cost compact unit utilizes a rugged metal enclosure and is intended for installation in control panels using DIN-rail mounting. This is a plug-and-play Ethernet switch which requires no The unit is powered from a choice of low-voltages (AC or DC). Redundant power connections are provided for back-up power schemes. LED indicators assist in troubleshooting network issues. configuration. All ports automatically configure their data rate Plug-and-Play operation DIN-rail mounting Rugged metal enclosure Diagnostic LEDs Auto-negotiation of speed and duplex Auto-MDIX supports cable inversion UL 508 listed, c-UL listed, CE mark
Open the catalog to page 1Overview The Skorpion Switch is intended for control panel installations where DIN-rail space is at a premium by requiring a width of only one inch (26 mm) of rail space. A metal DIN-rail clip attached to the aluminium enclosure can survive the toughest installation. A writable side label allows the installer an opportunity to document field cabling locations right on the unit. The switch can be powered from either a 10–36 VDC or 24 VAC (±10%) source. Its half-wave rectified low-voltage power supply allows the sharing of power with other 24 VAC/VDC control devices from a common power...
Open the catalog to page 2Specifications Power Requirements Operating Temperature Storage Temperature Relative Humidity Shipping Weight Ethernet Communications IEEE 802.3 10/100 Mbps data rate using RJ-45 connectors, 100 m (max) Green = 100 Mbps communication established Yellow = 10 Mbps communication established Flashing = data transmissions occurring Green = Full-duplex communication established Off = Half-duplex communication established Regulatory Compliance CE Mark; CFR 47, Part 15 Class A; RoHS; UL 508 Industrial Control Equipment Mechanical Drawing
Open the catalog to page 3Power Considerations Applied voltage must be in the specified range and deliver a current commensurate with power consumption. The recommended size for solid power conductors is 16-20 AWG; and for stranded conductors use 16-18 AWG. Zero volts (COM) is isolated from chassis (earth). Input connections are reverse-polarity protected. Connecting chassis to earth or using a backup source is always optional. All options shown are for use in Class 2 circuits. DC Powered AC Powered AC Powered with Redundant Redundant Grounded Secondary Power Power Typical Switch Installations Ethernet Switch Media...
Open the catalog to page 4All Contemporary Control Systems catalogs and technical brochures
-
DS-PC104220B
4 Pages
-
DS-AISRVR00B
6 Pages
-
TD9905200D
3 Pages
-
TD9905000D
3 Pages
-
TD0209000D
3 Pages
-
DS-EIS00000B
4 Pages
-
DS-EISK8PG0B
4 Pages
-
DS-EISKG800BA
4 Pages
-
DS-EISK5GH0B
4 Pages
-
DS-EISK5G00B
4 Pages
-
EXTEND-A-BUS Series
6 Pages
-
CANPCI Series
3 Pages
-
CAN104-DN
3 Pages
-
CANISA
3 Pages
-
BASgateway
4 Pages
-
Portable BASrouter
8 Pages
-
BASrouter
8 Pages
-
BASview
16 Pages
-
BAScontrol
8 Pages
-
BASremote
8 Pages
-
CTRLink®
6 Pages
Archived catalogs
-
ARCNET for Control
86 Pages