| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | Industrial Automation Products | | |
| | | |
| | | Pictograms | | |
| | | |
| | | Bus Specifications | | Board Size | | |
| | | |
| | | |
| | | Product is PCI Express standard compliant and can be used in the computer equipped with PCI Express bus expansion slot. | | Product is PCI standard/Low Profile compliant. A bracket for standard-size PCI slots is provided. | | |
| | | PCI Express | | |
| | | Low Profile | | |
| | | |
| | | |
| | | |
| | | |
| | | Supported Connectors | | |
| | | |
| | | Product is PCI standard compliant and can be used in the computer equipped with PCI bus expansion slot. | | |
| | | 100-pin 0.8mm Pitch | | 68-pin 0.8mm Pitch | | 37-pin D-SUB | | |
| | | PCI | | |
| | | |
| | | Digital Input/ Output | | |
| | | |
| | | |
| | | 96-pin Half Pitch | | 50-pin Mini-Ribbon | | |
| | | Product is USB standard compliant and can be used in the computer equipped with USB2.0/1.1 ports. Supports USB2.0 high-speed mode(480Mbps). Product supports Cardbus that is a 32-bit PC card standard bus. | | |
| | | USB 2.0 | | |
| | | |
| | | Indicates the number ofpins and shapes ofconnectors used for external connection. The supported cables and accessories will vary depending on these specifications. CONTEC provides a wide variety of cables and accessories to suit your needs. I Cables with connectors on both ends I Accessories (Terminal block, etc.) Q-07 | | |
| | | |
| | | |
| | | Card Bus | | |
| | | |
| | | DIGITAL I/O | | |
| | | |
| | | |
| | | Product supports 16-bit PC card standard. | | |
| | | |
| | | Interface boards that provide computers with digital signal I/O functions. They monitor the status (ON/OFF) of relays, operating switches and measurement devices as well as controlling (ON/OFF) lamps, 7-segment display units and relays. These boards can also be used as an interface for conducting digital communication with controllers such as PLC or microcomputers. | | |
| | | PCMCIA | | |
| | | |
| | | Cables with a connector on one end | | |
| | | |
| | | |
| | | Connector set | | |
| | | |
| | | I/O Points | | |
| | | |
| | | Maximum number of input channels | | Maximum number of output channels | | |
| | | Digital output | | |
| | | Digital input | | |
| | | | |
| | | |
| | | |
| | | mmmm | | |
| | | nnn | | |
| | | |
| | | |
| | | Maximum number of points(bits) that can be input / output | | |
| | | Bi-direct | | |
| | | |
| | | XX | | |
| | | |
| | | |
| | | |
| | | Supported softwares | | |
| | | |
| | | API-TOOL Drivers for Windows are provided. The license-free driver software (both development and runtime) provides commands to interface boards or cards using Windows standard Win32API function (DLL). | | |
| | | Windows Driver | | |
| | | |
| | | |
| | | Monitoring status of contact points and switches | | |
| | | |
| | | API-TOOL Drivers for Linux are provided. The license-free driver software (both development and runtime) that provide commands to interface boards or cards using module-style device drivers and the shared library. | | |
| | | Linux Diver | | |
| | | |
| | | Inputs ON/OFF signals | | |
| | | |
| | | |
| | | | LabVIEW | VI-DAQ, a VI library for use with National Instruments' LabVIEW can be downloaded from our Web site. With function format similar to that of LabVIEW's "Data acquisition VI", VI-DAQ set-up is not complicated therefor simplifying device operation. For the details, please visit: http//ww.contec.com/mldaq/ Points | | |
| | | Measurements of individual sensors Inputs BCD/binary data | | |
| | | |
| | | |
| | | I/O interface and internal logical circuits are insulated by Opto-couplers and relay contacts in order to prevent electrical interference with the PC. Requires additional power to drive external circuits. I/O interface and internal logical circuits are not insulated. These respond at a higher speed than insulated devices. | | I/O interface supports high-voltage circuits [those exceeding 24VDC]. Some have an output interface that supports AC. | | |
| | | High Voltage | | |
| | | Isolated | | |
| | | |
| | | |
| | | |
| | | Connecting with measurement devices/controllers | | |
| | | |
| | | Uses a high-speed Opto-coupler that enables a response of 1u to 5usec. | | |
| | | Nonisolated | | |
| | | Hi-Speed Opto-coupler | | |
| | | |
| | | Controls BCD / binary data Controlling Relays/lamps Outputs ON/OFF signals Motor control Controls BCD/binary data | | |
| | | |
| | | |
| | | |
| | | A power source is integrated on the device in order to drive input circuit Opto-couplers and I/O circuits. These are useful when additional power sources aren't available. | | Disables level (ON/OFF) changes that take place faster than the set value and prevents incorrect input due to noise and chattering. | | |
| | | Power On board | | | Digital Filter | | |
| | | | |
| | | |
| | | |
| | | I/O interface supports a current sourcing circuit. It is called "negative common" because the common polarity is reverse to that of a current sinking circuit. | | Output interface is equipped with a Zener diode that prevents damage and / or malfunction due to a surge in voltage and incoming current. | | |
| | | Negative Common | | | Surge Protection | | |
| | | | |
| | | |
| | | I/O interface supports both current sinking circuit and current sourcing circuit. | | Output interface is equipped with both a Zener diode which prevents damage and / or malfunction due to a surge in voltage and incoming current and a policing switch which guards against damage due to any current overages. | | |
| | | Surge & Overcurrent Protection | | |
| | | Non polarity | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | Global Portal : www.contec.com | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |