RPH
11Pages

Catalog excerpts

Clemco Industries Corp. • One Cable Car Drive • Washington, MO 63090 Phone: (636) 239-4300 • Fax: (636) 239-0788 Email: info@clemcoindustries.com www.clemcoindustries.com NOTICE TO PURCHASERS AND USERS OF OUR PRODUCTS AND THIS INFORMATIONAL MATERIAL The products described in this material, and the information relating to those products, is intended for knowledgeable, experienced users of abrasive blasting equipment. No representation is intended or made as to the suitability of the products described herein for any particular purpose of application. No representations are intended or made as to the efficiency, production rate, or the useful life of the products described herein. Any estimate regarding production rates or production finishes are the responsibility of the user and must be derived solely from the user’s experience and expertise, and must not be based on information in this material. The products described in this material may be combined by the user in a variety of ways for purposes determined solely by the user. No representations are intended or made as to the suitability or engineering balance of the combination of products determined by the user in his selection, nor as to the compliance with regulations or standard practice of such combinations of components or products. It is the responsibility of the knowledgeable, experienced users of the products mentioned in this material to familiarize themselves with the appropriate laws, regulations and safe practices that apply to these products, equipment that is connected to these products, and materials that may be used with these products. It is the responsibility of the user to insure that proper training of operators has been performed and a safe work environment is provided. Our company is proud to provide a variety of products to the abrasive blasting industry, and we have confidence that the professionals in our industry will utilize their knowledge and expertise in the safe efficient use of these products. OWNER’S MANUAL © 2011 CLEMCO INDUSTRIES CORP. • Stock No.: 21449 • Manual No.: 1168-0395 • Date of Issue: 3/95

Open the catalog to page 1

RPH DUST COLLECTOR 1.0 INTRODUCTION 1.1 Scope: This manual covers the assembly, installation, operation and maintenance of Zero RPH Reverse Pulse Jet Dust Collectors. Some equipment may vary slightly due to size and configuration. Drawings supplied with this manual apply to the specific dust collector provided. Use the drawings with the manual to assemble the collector and order replacement parts. The dust collector is one part of a larger system. This manual is to be used in conjunction with all other manuals provided with the equipment. 1.2.1 Clemco Industries Corp. uses signal...

Open the catalog to page 2

Solenoid Bank Diaphragm Pulse Valves Pressure Regulator Compressed air inlet Access Covers Exhaust Ducting Supplied by user Pulse Manifold Inlet Ducting Supplied by user Low Pressure Line (Higher Vacuum) High Pressure Line (Lower Vacuum) Filter Cartridge Differential Pressure Panel Assembly Sequence Panel Manifold Drain Petcock Dust Drum Lids Dust Drums WARNING Weight and bulk of the components may require that erection and placement of the collector be performed by personnel experienced with handling structural steel, and able to safely operate material handling equipment needed to erect...

Open the catalog to page 3

RPH DUST COLLECTOR2.2 Assembly 2.4 Exhauster Assembly CAUTION All seams assembled on the job site must be sealed to weather-tight condition. Use mastic tape and caulking on all seams as shown on the assembly drawings. 2.2.1 The degree of assembly depends on the size and style of the collector. There may be exceptions; but they are usually as follows: • RPH-2, RPH-3, RPH-6 & RPH-8: Factory assembled, each requires locating and anchoring to a sound footing, and assembly of the exhauster and ducting. • RPH-4, RPH-10, RPH-12, & RPH-16: Each requires field assembly of the leg/hopper assembly...

Open the catalog to page 4

Dust Collector Outlet Exhaust Ducting Supplied by user Inlet Ducting Supplied by user Exhaust Stack with Damper Ducting Support Flex Joint Fan Housing Electrical Connections WARNING Shorting electrical components could result in death, serious electrical shocks, or equipment damage. All electrical work, or any work done inside an electrical panel, must be performed by qualified electricians, and comply with applicable codes. NOTE: Wiring schematic for the sequence panel, exhauster motor, control panel and other electrical accessories are included when accessories are furnished by Clemco...

Open the catalog to page 5

Dust Containers 2.9.1 Attach a flex hose and dust drum lid to the bottom of the dust hopper. CAUTION The air source for the filter pulse must be 35 to 50 degrees Fahrenheit dew point and be free of any oil contaminants. If line air does not meet this requirement, an optional air dryer is recommended. Moisture or oil contaminants in the pulse system will decrease cartridge life and filtering efficiency 2.8.1 An air line must be supplied to the pressure regulator located on the pulse manifold inlet. The size of the line depends on the size of the collector. The compressor and piping supplying...

Open the catalog to page 6

RPH DUST COLLECTOR CAUTION Do not pulse new dust collectors or replacement cartridges until the cartridges are properly seasoned. See Section 6.2. Pulsing unseasoned cartridges could cause premature cartridge failure or decrease the efficiency of dust collector. 3.2.2 With the sequence switch off, pressurize the pulse manifold to 100 psi and check pneumatic connections for leaks. 3.2.3 Turn pulse pressure to 20 psi and switch the pulse sequence on. Check the air pulse and sequence of the diaphragm pulse valves, solenoids, and panel timer. After all items are checked, adjust the...

Open the catalog to page 7

RPH DUST COLLECTOR 5.0 PREVENTIVE MAINTENANCE _A WARNING Make sure the following conditions are met before performing any maintenance on the collector. • Turn off compressed air supply and drain air from pulse manifolds. • Turn off sequence control switch. Failure to observe the above warnings could result in serious injury from the sudden release of trapped compressed air or the operator losing balance. • Always wear a properly-fitted and maintained, NIOSH-approved respirator, eye protection and safety clothing when servicing dust-laden areas of the dust collector. Failure to do so could...

Open the catalog to page 8