Catalogs >
CHINO CORPORATION >
Digital Program Setter DP3000G

Digital Program Setter DP3000G
4Pages

Catalog excerpts

GRAPHIC PROGRAM SETTER DP3000G series is a graphic program setter employed high visibility 5.6" TFT color LCD display. Maximum 200 types of program pattern (Maximum 4000 steps) are stored and performance pattern is selectable. Setting output can be selected from high accuracy analog output (DC current/ voltage) and digital output with no setting errors using communications. Employing clear 5.6" TFT color LCD display Graphic screen of pattern progress status, display of PV Setting output signal value/SV value/pattern/step/time and various monitor func- tions such as enlarged data display and external input/out- 2 : Analog output (4 to 20mA) 4 : Analog output (0 to 10V) put status display are prepared. Easy program pattern settings on graphic screen 7 : Digital output (RS485) Communications interface *1 Maximum 200 patterns /Maximum 4000 steps settings, pattern repeat, linking between patterns and endless pro- gram setting are available. Time signal settings per step Time signal 30 types are selectable. Maximum 28 points external output assignment is available. Storing settings in CF card Setting management is easy as all settings including set- ting program pattern and each parameter are stored in C F card and readout from it. PC software allows you to edit program pattern and para- External input / output signal 0 : None OP Abundant external input / output functions 1 : Digital input/ output (non voltage contact input) Remote contact, pattern selection, time signal and status 2 : Digital input/ output signal output are available by digital input/output function. (External power supply spec for only input) OP Unit with external input 16 points and external output 28 Transmitter power supply points enables function assignment setting. 0 : None 1 : Transmitter power supply OP OP : Option *1 Rear port exclusive use for COM1, front and rear port switchable for COM2. *2 Option cannot be selected when setting output is 1 or 7 (digital output). *3 COM1 is setting output when setting output is 7 (RS485). Option cannot be selected when setting output is 1 (RS422A). *4 COM1 is setting output when setting output is 1 (RS422A). Option cannot be selected when setting output is 7 (RS485).

Open the catalog to page 1

OPERATION SCREEN Running status display at once Running status display of pattern progress, SV, time and time signal. (Enlarged data screen Enlarged display of SV and elapsed time (or remaining ILLI LfLI (External input status display screen (External output status display screen (Program pattern setting screen

Open the catalog to page 2

PROGRAMMING SPECIFICATIONS Pattern set type: Target temp(SV)/Time or Ramp rate/Time Time setting Hour/Minute or Minute/Second Ramp rate setting Temperature/Minute or Temperature/Second Number of steps: Up to 199 steps per pattern Number of patterns:Up to 200 patterns Total number of steps:Up to 4000 steps Repeat: Pattern --- Up to 9999 times, Step --- up to 99 times Step setup range: Target value --- Scale range Time --- 0 to 999 hours 59 minutes or 0 to 999 minutes 59 seconds Start temperature: Arbitrary set value start Target value (SV) correction: 99999 to 99999, decimal point linked...

Open the catalog to page 3

TERMINAL ARRANGEMENT Output (+) terminal Output (-) terminal Transmitter power supply terminals (option) Time signal Status External drive/ pattern selection/ DI terminals Setting output (digital) and communications interface (option) terminals COM1 COM2 Terminal RS232C RS485 RS422A Terminal RS232C RS485 RDA SA RD SA RD 6E 6I RDB SB SD SB SD 6F 6J SDA SG SG SG SG 6G 5J SDB 6H *COM1 is used for setter digital output SG 5J *RS422A: 1 port in COM1 only *COM1 is exclusive use for rear port, rear port and front port switchable for COM2. EXTERMINAL INPUT/OUTPUT TERMINALS Time signal output...

Open the catalog to page 4