Group: Industrial Process Instrumentation
Catalog excerpts
GRAPHIC PROGRAM CONTROLLER DP1000G series is a graphic program controller employed high visibility 5.6 TFT color LCD display. Maximum 200 types of program pattern (Maximum 4000 steps) are stored and performance pattern is selectable. Control cycle of 0.1 sec, 5 digits display, high speed and high accuracy of 0.1% indicating accuracy are realized. FEATURES Employing clear 5.6 TFT color LCD display Graphic screen of pattern progress status, display of PV value/SV value/pattern/step/time and various monitor functions such as program progress enlarged display, enlarged data display and bargraph display are prepared. Easy program pattern settings on graphic screen Maximum 200 patterns/Maximum 4000 steps settings, pattern repeat, linking between patterns and endless program setting are available. Parameter settings per step Each parameter setting such as SV/PV start, guarantee soak and time signal is available per step. High performance and universal input Input selection from each range of thermocouple, DC voltage/current and resistance thermometer are available and unit has performance of 5 digit display, accuracy rating of 0.1% and sampling period of 0.1sec. Storing settings in CF card Setting management is easy as all settings including setting program pattern and each parameter are stored in CF card and readout from it. PC software allows you to edit program pattern and parameter. Various control application functions Heating/cooling output is applicable as control output has ON-OFF pulse type, current output type, SSR drive pulse type and voltage output type. Abundant external input/output Unit with external input 16 points and external output 28 points enables function assignment. Synchronized operation with peripherals are easy. Serial communications interface and transmission signal output are also prepared. G Control mode (output No.1) 1 : ON-OFF pulse PID 2 : ON-OFF servo PID (standard load spec) 3 : Current output PID (general type 4 to 20mA DC) 5 : SSR drive pulse PID 6 : Voltage output PID (general type 0 to 10V DC) 8 : ON-OFF servo PID (minimal load spec) A : Current output PID (high accuracy type 4 to 20mA DC) B : Current output PID (high accuracy type 1 to 5mA DC) C: Voltage output PID (high accuracy type 0 to 10V DC) Control mode (output No.2) 0 : None 1 : ON-OFF pulse PID*1 OP 3 : Current output PID (general type 4 to 20mA DC) *1 OP 5 : SSR drive pulse PID*1 OP 6 : Voltage output PID (general type 0 to 10V DC)*1 OP A : Current output PID (high accuracy type 4 to 20mA DC)*1 OP B : Current output PID (high accuracy type 1 to 5mA DC)*1 OP C: Voltage output PID (high accuracy type 0 to 10V DC)*1 OP Communications interface 0 : None R: RS232C (COM1)OP S : RS485 (COM1)OP A : RS422A (COM1)OP B : RS232C (COM1) + RS232C (COM2)OP C: RS485 (COM1) + RS232C (COM2)OP D: RS422A (COM1) + RS232C (COM2)OP E : RS232C (COM1) + RS485 (COM2)OP F : RS485 (COM1) + RS485 (COM2)OP G: RS422A (COM1) + RS485 (COM2)OP Transmission signal output 1 0 : None 1 : 4 to 20mAOP 2 : 0 to 1VOP 3 : 0 to 10VOP 4 : 1 to 5VOP Transmission signal output 2 0 : None* 1 : 4 to 20mAOP 2 : 0 to 1VOP 3 : 0 to 10VOP (Adding only transmission signal output 2 is not available) Case color G: Gray B : Black External input/ output signal 0 : NoneOP 1 : Digital input/ output (non voltage contact input) 2 : Digital input/ output (External power supply spec for only input)OP Transmitter power supply 0 : None 1 : Transmitter power supplyOP Interchangeable with DP series DP series are easily replaced with DP1000G which inherited characteristics of DP series such as function, operability and terminal arrangement/configuration. Selectable when control mode (output1) is 1,3,5,6,A,B,C. COM1 is exclusive use for rear port, COM2 is rear port and front port switchable. OP Option
Open the catalog to page 1OPERATION SCREEN Running status display at once Running status display of pattern progress and PV/ SV/ ►Trend screen Enlarged trend display of PV and SV ► Enlarged data screen Enlarged display of PV/SV Bargraph screen ►Step parameter setting screen
Open the catalog to page 2INPUT SPECIFICATIONS Input types: 10mV, 20mV, 50mV, 100mV, 5V, 10V DC current --- 20mA Thermocouple --- B, R, S, K, E, J, T, N, U, L, WRe5-WRe26, W-WRe26, NiMo-Ni, CR-AuFe, PR5-20, PtRh40-PtRh20,Platinel2 Resistance thermometer --- Pt100, JPt100, old Pt100, Pt50, Pt-Co *3 wire and 4 wire Accuracy rating: Refer to the table of measuring range and accuracy ratings Reference junction compensation accuracy: K, E, J, T, N, Platinel2 --- 0.5 or less Other than above --- 1.0 or less Sensor correction: Selectable by 0.1time resolution of the target resolution Sampling period: Approx 0.1 sec...
Open the catalog to page 3-99999 to 99999, decimal point linked with scaling Setting range: Dead band: 0.1 times of set resolution Delay setting range:1 to 10 times Output type: Relay contact output 4 points --- (A contact, 1 common) Contact capacity --- Resistance load 100 to 240VAC 30VDC, 3A or less Inductive load 100 to 240VAC 30VDC, 1.5A or less External output signal assignment 4 points (for extended assignment setting) Alarm reset: Alarm can be cleared during occurrence EXTERNAL OUTPUT SIGNAL SPECIFICATION Number of output: 28 points (function assignment per point) Output type: Open collector output (24V DC,...
Open the catalog to page 4PERFORMANCE SPECIFICATION MEASURING RANGES ACCURACY RATINGS 'Accuracy converted to the measuring range under the reference operation condition. Reference junction compensation accuracy is added to thermocouple. WRe5-WRe26, W-WRe26, NiMo-Ni, Platinein, CR-AuFe, PtRh40-PtRh20 : ASTM Vol. 14.03
Open the catalog to page 5TERMINAL ARRANGEMENT Control output terminals (Output1) Current/ voltage/ SSR drive pulse type (+) Current/ voltage/ SSR drive pulse type (-) On-off servo type On-off pulse type Transmitter power supply terminals (option) Time signal Status External drive/ pattern selection/ DI terminals AL1 AL2 Alarm output terminals AL3 AL4 COM Output (+) terminal Output (-) terminal Resistance thermometer-4 wire type (A) terminal Thermocouple/DC voltage/DC current (+) terminal Resistance thermometer-3 wire, 4 wire type (A) terminal Thermocouple/ DC voltage/ DC current (-) terminal Resistance...
Open the catalog to page 6All CHINO CORPORATION catalogs and technical brochures
-
Pt-Co Temperature Probe
2 Pages
-
LH100
4 Pages
-
ELECTRONIC MINI-RECORDER
2 Pages
-
MR SERIES CARD LOGGERS
8 Pages
-
IR-BAT SERIES
4 Pages
-
IR-FA SERIES
6 Pages
-
IR-TA SERIES
2 Pages
-
MODEL IR-TE
2 Pages
-
IR-CZQW series
2 Pages
-
TRAMS III
4 Pages
-
General Catalog
14 Pages
-
IR-CZQH
2 Pages
-
On-line model
12 Pages
-
C800
4 Pages
-
KT-H503/KT-H504
2 Pages
-
IR-R0A
2 Pages
-
R000
4 Pages
-
HN-EK
2 Pages
-
HN-EH
2 Pages
-
IR-HA
2 Pages
-
IR-TE
2 Pages
-
DP2000G
4 Pages
-
KP3000
6 Pages
-
AL4000 Dot-printing
6 Pages
-
AH4000 Dot-printing
6 Pages
-
KR3S
6 Pages
-
KR5100
4 Pages
-
HYBRID MEMORY RECORDER
8 Pages
-
GRAPHIC RECORDER
6 Pages
-
IR-BZ
2 Pages
-
MILA-C5000PN
4 Pages
-
Three-Phase JW
6 Pages
-
Single-phase JU
4 Pages
-
On-line model IR-SA
4 Pages
-
Strip Chart Recorder ES600
2 Pages
-
KR3000
6 Pages
-
Sheathed Thermocouples
12 Pages
-
Solidpak NC
6 Pages
-
Fiber optic model
6 Pages
-
Thermal Imaging Sensor
4 Pages
-
Digital Program Setter
6 Pages
-
Data Scanner
4 Pages
-
Hybrid Recorder
6 Pages
-
Hybrid Memory Recorder
6 Pages
Archived catalogs
-
SOFC Testing System FC5300
1 Pages
-
TP-S ( Termal image )
2 Pages
-
TP
4 Pages
-
EH3000 PEN
4 Pages
-
KH4000
6 Pages
-
KL4000
6 Pages
-
AH4000 PEN
8 Pages
-
AL4000 PEN
6 Pages
-
KR2S
6 Pages
-
Temperature Logger: MR5300
8 Pages
-
Strip Chart Recorder: LE5000
8 Pages
-
Graphic Recorder: KR2000
6 Pages
-
Ubiquitous Recorder
4 Pages