UTS - 12 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

Catalogue excerpts

Metallic Magnetic Drive Process Centrifugal Pumps UTSHE / UTS-BHE Comply to : 2006/42/CE Design to : ISO 2858 / EN 22858 (ex DIN 24256) ISO 5199 - UNI 15783 ATEX 100 Directive 94/9/EC Flanged UTS-B Close Coupled Execution Metallic Magnetic drive Horizontal - Single Stage - Process Centrifugal pumps Materials : AISI 316 (1.4408) Close-coupled and End-suction executions

 Open the catalogue to page 1

UTS SERIES Mag drive concept Suitable for handling aggressive, toxic and The synchronous drive configuration is based on an outer magnet ring back pull-out principle and a strong bearing housing with hazardous liquids (low viscosity, clean or slightly contaminated) in the chemical, petrochemical standards is the first requirement. The UTS are made by stainless steel AISI together by the flux of attracting magnet poles flowing through the containment isolation shell. 316 : on bare shaft execution, the pump is These two magnet rings are locked also equipped as a standard with reliable oil lubricated...

 Open the catalogue to page 2

UTS SERIES Inner and Outer magnets are equipped with NdFeB (neodymium iron boron) handling, self-venting . permanent magnets. Patented cage magnet attachment guarantees Internal Flushing paths developed to remove the maximum amount of heat generated by the bushing rotation and Eddie Current on the Isolation Shell. The problem of reverse rotation during start-up has been eliminated thanks to the key driven system. Renewable wear ring as standard. The design allows to the Isolation Shell to be The pump design configuration of either end-suction or close-coupled design. self-venting. The standard...

 Open the catalogue to page 3

features CASING • Bonus casing thickness : minimum (1.4408) closed impeller design maximizes casing life against provides maximum efficiency and • Standard casing drain for a • Standard back vanes reduce axial complete and fast draining of the thrust and seal chamber pressures to guarantee an extraordinary bearing and seal life • Heating \ Cooling jacket option available ISOLATION SHELL BUSHING SUPPORT • The design allow to the Isolation • Internal flushing paths Shell to be self-venting and fully drainable. • The rib on the bottom is a perfect vortex breaker which increase the life time. • Isolation...

 Open the catalogue to page 4

painting coating quality STATIC AND ROTATING bushingS • The rotating metallic shaft is installed inside a SiC Bushing supported The metal surfaces are protected by a by double static bushings : this design grants a long service life time high performance three coating layers sharing equally the mechanical efforts • Optional : Static Graphite Bushings • Epoxy zinc paint • Epoxy amidic modified vinyl • Epoxy enamel paint or aliphatic acrylic polyurethane Available upon request : EN ISO 12944-5 C5M and C5I protecting paint system grades. HIGH TEMPERATURE EXECUTION Inner and Outer magnets are equipped...

 Open the catalogue to page 5

SECTIONAL DRAWING I° FRAME Isolation Shell Pump Shaft UTS-B : 0.75 kW (motor size 80) -> 18.5 kW (motor size 160) UTS : 0.75 kW (motor size 80) -> 18.5 kW (motor size 160) Temperature range UTS-B : -40 °C* -> +180 °C UTS : -40 °C* -> +300 °C * -100 °C special execution Bearing bracket Allowable Pressure Range Bushings Support UNI 1092-1 / ISO 7005-1 PN 16, type B upon request, drilling slotted to match ANSI 150 PTFE \ Grafoil Flange Connections Spacer Ring PTFE \ Armored Grafoil Thrust Bearing Bearing Sleeve Bearing Bush SiC \ Graphite \ PEEK \ RunSafeSiC Inner Magnet Outer Magnet Viscosity Allowable...

 Open the catalogue to page 6

SECTIONAL DRAWING II° FRAME Temperature range Allowable Pressure Range Flange Connections UNI 1092-1 / ISO 7005-1 PN 16, type B upon request, drilling slotted to match ANSI 150 Viscosity Allowable Solids Max concentration 2 % by weight Max particle size 0,15 mm Isolation Shell Pump Shaft Bearing bracket Bushings Support UTS-B : -40 °C* -> +180 °C UTS : -40 °C* -> +300 °C * -100 °C special execution UTS-B : 1,1 kW (motor size 80) -> 18.5 kW (motor size 160) UTS : 1,1 kW (motor size 80) -> 55 kW (motor size 250) Part list Technical Specifications Electric Motors PTFE \ Grafoil Spacer Ring PTFE \...

 Open the catalogue to page 7

Not binding data refers to water at room temperature. For specific performance curve contact CDR Pompe SpA.

 Open the catalogue to page 8

Not binding data refers to water at room temperature. For specific performance curve contact CDR Pompe SpA.

 Open the catalogue to page 9

Pump Size UTS-B I° FRAME Pump model *II° FRAME PUMP ARRANGED AS A I° FRAME FLANGE UNI EN 1092-1 PN 16RF Upon request slotted to ANSI 150 Motor Size ()* for motor size 160 - L4 according to manufacturing dimension OVERALL DIMENSIONS ()* for motor size 132 - 160 - L4 according to manufacturing dimension ** II° Frame executed as a I° Frame

 Open the catalogue to page 10

UTS Long Coupled - Baseplate installation OVERALL DIMENSIONS Motor Frame Pump model Pump model Motor Frame Motor Frame UTS I° FRAME Motor Frame *L4 according to manufacturing dimension *L4 according to manufacturing dimension

 Open the catalogue to page 11

For further info, please visit www.cdrpompe.com Pompe S.P.A. C.D.R. Pompe S.p.A. Via P. Togliatti, 26/A - 20030 Senago (MI) - Italy Tel. +39029901941 Technical Characteristics The technical data and characteristics stated in this General Catalogue are not binding. CDR Pompe S.p.a. reserves the right to make modifications without notice. Therefore data, dimensions, performances and any other stated issues are indicative only and not binding. Anyway for any technical details you must require an up-to-date product technical card.

 Open the catalogue to page 12

All C.D.R. Pompe catalogues and technical brochures

  1. UCS / UCS-B

    8 Pages

    En
  2. UCL / UCL-B

    12 Pages

    En
  3. UTN-L / UTN-BL

    12 Pages

    En
  4. UCN-L / UCN-BL

    12 Pages

    En
  5. STN series

    8 Pages

    En
  6. HTS series

    4 Pages

    En
  7. ETN series

    8 Pages

    En
  8. ETS series

    8 Pages

    En
  9. HTN

    4 Pages

    En

Archived catalogues