| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | IDM1553 | | |
| | | |
| | | 53(2.100) | | 6.4 (.250) MAX | | |
| | | The product assurance programme defines manufacturing procedures, establishes quality standards, in line inspection controls and 100% screening tests. The standard 100% screening performed prior to product shipment is shown in the flow chart. Manufactured in accordance with procedures laid down within MIL-STD-883 and BS9450 (CECC 63000). 100 per cent Screening | | |
| | | : | | |
| | | 6.3 (.250) | | |
| | | |
| | | |
| | | 48(1.900) | | |
| | | |
| | | 2.54 (.100) | | |
| | | |
| | | |
| | | - | | |
| | | |
| | | 46 (1.800) | | 1.27 (.050) | | |
| | | |
| | | 00000c (f4 ooooooo | | |
| | | 'ooooooo 4IÛOOOOOO | | |
| | | a. ùJ < 5 5.8 co X | | |
| | | |
| | | |
| | | |
| | | (BOTTOM VIEW) pin numbers are for reference »0000000 ooooooo78 | | |
| | | |
| | | |
| | | 2.54 (.100) TYP (TOL. NONCUM) | | |
| | | 1.4 (.056) dia glass bead (78 places) | | |
| | | | | | | | | | | | | | | STABILIZATION | | TEMP. | | | | LID SEAL | | BAKE | | CYCLE | | | | | | FCES6551 | | FCES6552 | | | | | | | | | | | | |
| | | |
| | | |
| | | Dimensions in millimetres (inches) | | |
| | | |
| | | Fig. 7 Mechanical Outline (DDIP) | | |
| | | |
| | | 56.8 (2.236) | | 5.00 max (0.197) | | |
| | | \ | | |
| | | |
| | | |
| | | 2.63 (0.104) | | |
| | | 2.92(0.115) | | |
| | | „ 40 equal pitches of 1.27 (0.05) ^—:--T | | |
| | | |
| | | |
| | | |
| | | ^_I GROSS LEAK | | |
| | | |
| | | 8(0.315) | | |
| | | |
| | | ^ 0.25(0. | | |
| | | ^0.38(0.015) Dimensions in millimetres (inches) | | |
| | | 01) | | |
| | | |
| | | O | | |
| | | □ | | |
| | | A | | |
| | | MANUFACTURING OPERATION | | |
| | | |
| | | HYBRID TEST | | |
| | | O.C. INSPECTION | | |
| | | |
| | | |
| | | | |
| | | |
| | | |
| | | Fig. 8 Mechanical Outline (Flatpack) | | |
| | | | | | | | | | | | Title | Factory Procedure | BS 9450 Requirement | MIL-STD-883 Requirement | | | | Internal Visual | FCES6360 | 1.2.10 | 2017 | | | | Lid Seal | Welded | 1.2.6.14 | none | | | | Stabilization Bake | FCES 6551 | 1.2.6.3.4 | 1008 | | | | Temperature Cycling | FCES 6552 | 1.2.6.13 | 1010 | | | | Constant Acceleration | FCES 6380 | 1.2.6.9 | 2001 | | | | Fine Leak | FCES 6370 | 1.2.6.14.1 | 1014 | | | | Gross Leak | FCES 6370 | 1.2.6.14.2 | 1014 | | | | Burn In | FCES 6390 | 1.2.9.2 | 1015 | | | | Final QC | FCES 6560 FCES 6376 FCES 6377 FCES 6370 | 1.2.2 | 2009 | | | | | | | | | | | |
| | | |
| | | ORDERING INFORMATION IDM1553-XX-X X Case style D = DIL FP = Flat Pack | | |
| | | |
| | | PROM firmware revision 1 = Standard TRANSCEIVER Voltage type 05 - +5v only 15 - +5v and -15v | | |
| | | |
| | | |
| | | Fig. 10 Quality Conformance | | |
| | | Fig. 9 Ordering Information | | |
| | | |
| | | |
| | | Product Safety Operation outside the stated ratings may result in premature failure or safety hazard. Product safety information is available on request. | | |
| | | All information contained herein is given in good faith, but unless we have given the user written confirmation of product suitability we can accept no liability regarding the particular application for which the product is intended. | | C-MAC reserves the right to make changes to the product described in this data sheet to improve performance, reliability or manufacturability. | | |
| | | |
| | | |
| | | |
| | | tmÊmÊÊÊmÊÊÊmmimmÊÊÊÊÊmÊmHmmmKÊÊmKÊÊÊÊÊmÊmmtmÊÊmmmmÊmmmmmtÊmmmtm | | |
| | | |
| | | C-MAC Microcircuits Limited, South Denes, Great Yarmouth, Norfolk, NR30 3PX England Telephone: +44 (0) 1493 743100 Fax: 44 (0) 1493 858536 | | |
| | | .US. | | |
| | | cum | | |
| | | s - | | |
| | | |
| | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |