Modular planetary gearboxes
560Pages

{{requestButtons}}

Catalog excerpts

Modular planetary gearboxes - 1

300M series Modular planetary gearboxes We have a relentless commitment to excellence, innovation and sustainability. Our team creates, distributes and services world-class power transmission and drive solutions to keep the world in motion. HEADQUARTERS Bonfiglioli Riduttori S.p.A. Via Giovanni XXIII, 7/A 40012 Lippo di Calderara di Reno Bologna (Italy) tel: +39 051 647 3111 fax: +39 051 647 3126 bonfiglioli@bonfiglioli.com www.bonfiglioli.com

Open the catalog to page 1
Modular planetary gearboxes - 3

GENERAL INFORMATION 12 Service factor requested by application 11 SERIES 300M MODULAR PLANETARY GEARBOXES 23 Surface protection and painting options 37 NEGATIVE MULTIDISC BRAKE AND HYDRAULIC MOTORS PLANETARY GEARBOX SERIES 300M ATEX CONFIGURATION A4 Peculiarities of 300M series gear units 482 compliant with directive Atex A5 Ordering numbers 490 ELECTRIC MOTORS M6 DC brake motors type BN and M_FD 511 M7 AC brake motors type BN and M_FA 515 Revisions Refer to page 556 for the catalogue revision index. Visit www.bonfiglioli.com to search for...

Open the catalog to page 3
Modular planetary gearboxes - 4

SYMBOLS AND UNITS OF MEASURE Ac 1,2 [N] Calculated thrust load An 1,2 [N] Rated thrust load Thrust load at gearbox output shaft Lifetime factor for gearbox calculation Lifetime factor for bearing calculation Speed factor referred to input and output shaft loading Load corrective factor on shafts Service factor required by the application Reduction ratio Rated radial load at gearbox re-calculated with respect to different load application points Axial load duty factor Ambient temperature Radial load factor Intermittence factor Torque delivered to output shaft Calculated torque at...

Open the catalog to page 4
Modular planetary gearboxes - 5

Symbol referring to weight of gearboxes. The number associated with the wrench symbol indicates the tightening torque for friction coupling screws. Columns marked with this symbol indicate the reference page showing dimensions. Negative multidisc brake. This symbol identifies reference page number. Hydraulic motor connection. DANGER - WARNING This symbol indicates situations of danger, which if ignored, may result in serious injury to the operator. IMPORTANT This symbol indicates important technical information. Apply to equipment complying with “ATEX” Directive Cover for standard input...

Open the catalog to page 5
Modular planetary gearboxes - 6

INTRODUCTION This catalogue presents BONFIGLIOLI RIDUTTORI’s range of Series 300M modular planetary gearboxes. The range has been expanded and integrated with new sizes, technical improvements and enhanced modularity right through to the larger sizes. This feature signifies greater flexibility in internal production to ensure quick availability of products in the sizes and types requested either directly from the company or from the many affiliates belonging to the BONFIGLIOLI sales network in various countries around the world. The gearboxes are tested in conformity with the following...

Open the catalog to page 6
Modular planetary gearboxes - 7

The 300M series consist of a range of multi-purpose planetary gearboxes that can be operated by either hydraulic or electric motors. Basic features are: • 20 frame sizes of modular design • output torque up to 1,286,700 Nm • transmissible power up to 1050 kW • ratios from 3.4:1 to 5234:1 • versions: - in-line with 1 to 4 reductions - right angle (spiral bevel gear set into first stage) with 2 to 4 reductions • combinations with: - worm gear units - bevel-helical gear units • flange, foot and shaft mounting arrangements • slow output shafts: keyed, splined male, splined hollow, shrink disk...

Open the catalog to page 7
Modular planetary gearboxes - 8

CD_5 VERSIONS 1 Orbital hydraulic motor MG with/without brake 2 Hydraulic motor 3 Hydraulic motor setting 4 Cover 5 Negative brake 6 Compact electric motor 7 IEC electric motor 8 Electric motor setting 9 Electric motor connection with integrated fan 10 Input shaft 11 Solid input shaft with fan 12 Right-angle reduction stage 13 Single planetary reduction stage 14 Two or more planetary reduction stages 15 Planetary reduction combined with wormgear unit 16 Planetary reduction stage combined with helical bevel gear unit 17 MC/MZ - Keyed or splined solid shaft output 18 HC/HZ - Keyed or splined...

Open the catalog to page 8
Modular planetary gearboxes - 10

GENERAL INFORMATION The following paragraphs contain information on essential elements for selection and correct use of gearmotors. It is the significant value for the size. It is equivalent to the maximum value of nominal torque Mn2 for a life factor n2 x h = 10000 (referred to single stage configuration L1). 6.2 Rated output torque Mn2 [Nm] It is the output torque which the gearbox can transmit with steady load under working condition specified in the calculation method. ©Bonfiglioli Riduttori

Open the catalog to page 10
Modular planetary gearboxes - 11

Maximun torque M2max [Nm] It is the output torque that the gearbox can withstand under static or almost static conditions. It is generally meant as a momentary peak load or starting-up torque under load. The values in the tables are valid only in versions with output splined shaft (accessories excluded). Required torque Mr2 [Nm] The torque drawn by the application. It must always be equal to or less than rated output torque Mn2 for the gearbox under study. Input rated power Pn1 [kW] Pn1 is the maximum power that can be safely applied to the gearbox when the same is operated: - at a n1 drive...

Open the catalog to page 11
Modular planetary gearboxes - 12

CD_8 EFFICIENCY 8.1 Dynamic efficiency nd The parameter is defined as the relationship of the net power delivered to the output shaft P2 to the power applied to the input shaft P1: Indicative values for the efficiency are listed in the chart here after. It is defined as the relationship of the speed the input shaft is driven at and the speed delivered at the output shaft of a gearbox. 10.1 Input speed n1 [min -1] The speed the gearbox is driven at. The value is coincident with the motor speed if this is directly connected to the gearbox. Input speed should never exceed the n1max value...

Open the catalog to page 12
Modular planetary gearboxes - 13

12 SERVICE FACTOR REQUESTED BY APPLICATION fS' It's a coefficient that represents the severity of the application. This factor takes into account, although approximately, the type of load the gearbox operates with, the specific duty cycle as well as the operating daily hours. The table (A4) is of reference when determining the appropriate service factor for the application. Factor resulting by multiplying angular speed at input (n1) or output (n2) by actual operating working hours h, break times excluded. Life factor is directly proportional to gearbox rpms during the whole duty time...

Open the catalog to page 13

All Bonfiglioli catalogs and technical brochures

  1. HDP

    88 Pages

  2. Wind Solutions

    24 Pages

  3. 610X Series

    2 Pages

  4. 600Y3 Series

    2 Pages

  5. 600W series

    2 Pages