S30, 10-30V dc

DownloadPDF

Data Sheet

ModelsSensing Mode/LED*RangeCable**OutputTypeExcess GainBeam Pattern

S306E Emitter S306EQ Emitter 4-Pin Euro QD

–

PHOTOELECTRICS S30SN6R S30SN6RQ 60 m2 m 2 m 4-Pin Euro QD

NPN

EGCO-23(p. 429)BPO-23(p. 451) S30SP6R
OPPOSED 2 m S30SP6RQ 4-Pin Euro QD

PNP

S30SN6LP 2 m S30SN6LPQ S30SP6LP

P

4-Pin Euro QD

NPN

6 m
† EGCR-33(p. 433)BPR-30(p. 454) 2 m S30SP6LPQ
POLAR RETRO 4-Pin Euro QD

PNP

S30SN6FF200 S30SN6FF200Q 4-Pin Euro QD

NPN

116157 0 - 200 mmCutoff2 m
EGCF-24(p. 442)— S30SP6FF200 2 m S30SP6FF200Q 4-Pin Euro QD

PNP

S30SN6FF400 S30SN6FF400Q 0 - 400 mmCutoff2 m 4-Pin Euro QD

NPN

EGCF-25(p. 442)— S30SP6FF400 2 m S30SP6FF400Q
FIXED-FIELD 4-Pin Euro QD

PNP

S30SN6FF600 S30SN6FF600Q 0 - 600 mmCutoff2 m 4-Pin Euro QD

NPN

EGCF-26(p. 442)— S30SP6FF600 2 m S30SP6FF600Q 4-Pin Euro QD

PNP

* INFRARED LED W/30 to the 2 m model number (example, Visible Red LED ** For 9 m cable, add S30SP6LP W/30 ). A QD model requires a mating cable (see page 380). † Retroreflective range is specified using one model BRT-3 retroreflector. Actual sensing range may differ, depending on efficiency and reflective area of the retroreflector in use. See Accessories for more information.

S30 DC Specifications

Supply Voltage and Current 10 to 30V dc (10% max. ripple); Supply current (exclusive of load current): Opposed Mode Emitters: 25 mA Opposed Mode Receivers: 20 mA Polarized Retroreflective: 30 mA Fixed-field: 35 mA Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration Solid-state complementary (SPDT); Choose NPN (current sinking) or PNP (current sourcing) models.The Dark Operate (DO) output may be wired as a normally open marginal signal alarm output, depending upon hookup to the power supply. Output Rating 150 mA max. (each) in standard hookup; When wired for alarm output, the total load may not exceed 150 mA Off-state leakage current: less than 1 mA at 30V dc On-state saturation voltage: less than 1V at 10 mA dc; less than 1.5V at 150 mA dc Output Protection Circuitry Protected against false pulse on power-up and continuous overload or short circuit of outputs Output Response Time Opposed: 3 milliseconds ON, 1.5 milliseconds OFF Polarized Retroreflective and Fixed-field: 3 milliseconds ON/OFFNOTE: 100 millisecond delay on power-up; outputs are non-conducting during this time RepeatabilityOpposed: 375 microseconds; Polarized Retroreflective and Fixed-field: 750 microseconds. Repeatability and response are independent of signal strength. Indicators Two LEDs: Green and Yellow Green ON steady: power to sensor is ON Green flashing: output is overloaded (dc models only) Yellow ON steady: Light Operate (LO) is energized Yellow flashing: excess gain marginal (1-1.5x) in light condition, LO is energized

116

More information online at

bannerengineering.com