Q50 Series

L-GAGE

®

Sensors

Q50 Analog Output Specifications

Sensing BeamWave length: Q50..V: 685 nm (typical) Q50..: 880 nm (typical) Beam Size: Q50..V: 20 mm dia. (max.) Q50..: 20 mm dia. (max.) Sensing RangeQ50AV: 50 to 150 mm Q50A: 50 to 200 mm Q50BV: 100 to 300 mm Q50B: 100 to 400 mm Supply Voltage and Current 15 to 30V dc (10% max. ripple); 70 mA max. (exclusive of load) Supply Protection Circuitry Protected against reverse polarity and transient overvoltages Output Configuration Depending on model 4-20 mA current sourcing models: 1 k max. load @ 24V dc. Max. load = [(Vcc -4.5)/0.02] 0-10V voltage sourcing models: 15 mA max. Delay at Power-up 2 seconds Output Protection Protected against short circuit conditions Output Response TimeAnalog Output Average Interval Update Rate -3 dB Frequency Response Fast: 4 milliseconds 1 millisecond 112 Hz Slow: 64 milliseconds 4 milliseconds 7 Hz Resolution See RRC-5 and RRC-6 on page 468 for typical value. 200 mm, Slow Response: 1 mm (max), Fast Response: 4 mm (max) 100 mm, Slow Response: 0.5 mm (max), Fast Response: 2 mm (max) LinearityQ50B.. models: Q50B models: Target Distance: Q50A models: Target Distance: ±3 mm Q50A.. models: ±1.5 mm Color Sensitivity (typical) See charts CSC-4 and CSC-5 on page 469. Remote and Speed Input ImpedanceQ50B.. models: From 0° to 50° C: -0.25 mm/° C From -10° to 55° C: -0.35 mm/° C Q50A.. models: From 0° to 50° C: 0.08 mm/° C From -10° to 55° C: 0.11 mm/° C Remote and Speed Input Impedance 15 k Remote TEACH InputTo Teach: Connect gray wire to +5 to 30V dc To Disable: Connect gray wire to 0 to +2V dc (or open connection)
MEASUREMENT & INSPECTION AdjustmentsFast Speed: Connect black wire to +5 to 30V dc Slow Speed: Connect black wire to 0 to +2V dc (or open connection) IndicatorsRange LED Green — Target is within sensing range Indicator Red — Target is outside sensing range (green/red) OFF — Sensor Power OFF Teach/Output Yellow — Target is within taught window limits LED Indicator OFF — Target is outside taught window limits (yellow/red) Red — Sensor is in TEACH mode Ambient Light Immunity < 10,000 LUX ConstructionHousing: Molded ABS/Polycarbonate Hardware: M3 hardware is included. Window Lens: Acrylic Environmental Rating IEC IP67; NEMA 6P Connections 2 m or 9 m 5-conductor PVC-covered attached cable or 5-pin Euro-style quick-disconnect. See page 382. Operating ConditionsTemperature: -10° to +55° C Relative humidity: 90% at +50° C (non-condensing) Vibration and Mechanical Shock All models meet Mil. Std. 202F requirements. Method 201A (Vibration: 10 to 60Hz max. double amplitude 0.06”, maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G, 11 milliseconds duration, half sine wave. Application Notes Allow 15-minute warm-up for maximum performance Certifications Contact factory for more information. Hookup Diagrams MI09 (p. 494)

284

More information online at

bannerengineering.com