50 MHz Dual Channel Arbitrary Waveform / Function Generator - B&K Precision - #4

Text version of the page

Kat-SV-2009-Intro-0209:Kat-SV-2007-Intro.qxd table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:13.00pt "Arial", sans-serif; } .font1 { font:7.00pt "Microsoft Sans Serif", sans-serif; } .font2 { font:8.00pt "Microsoft Sans Serif", sans-serif; } .font3 { font:9.00pt "Microsoft Sans Serif", sans-serif; } .font4 { font:5.00pt "Verdana", sans-serif; } 50 MHz Arbitrary / Function Generators Models 4076 & 4079 Spécification s models 4076 4079 Channels 1 Channel | 2 Channels Frequency Characteristics Sine 1 jUHz to 50 MHz Square 1 jUHz to 50 MHz Triangle, Ramp 1 jUHz to 5 MHz Pulse 0.5 mHz to 25 MHz Accuracy 0.001 % (10 ppm) Resolution 12 digits or 1 jUHz Arbitrary Characteristics Built-in Waveforms Sine, Triangle, Square, Noise, Ramp Up, Ramp Down, Sine(X)/X, Exponential Up, Exponential Down, Gaussian Waveform Length 2 points to 4,000,000 points Vertical Resolution 14 bits (16,384 levels) Noise Add 1°% to 100°% to output waveform Sampling Rate 125 MSa/s, Point execution rate adjustable from 8 ns-100 s Frequency Accuracy: 0.001°% (10 ppm) Resolution: 4 digits or 1 ps Output Characteristics Amplitude Range 10 mV to 10 Vp-p into 50 Q Amplitude Resolution 3 digits (1000 counts) Amplitude Accuracy (1 kHz) ± 1% ± 20 mV of programmed output from 1 V - 10 V Flatness (relative to 1 kHz) ± 0.1 dB to 10 MHz ± 1 dB to 50 MHz Offset Range ± 4.99 V into 50 Q, depending on the Amplitude setting Offset Resolution 10 mV with 3 digits resolution Offset Accuracy ± 1% ± 10 mV into 50 Q Output Impedance 50 Q typical Output Protection The instrumenta output is protected against short circuit or nominal accidental voltages applied to the main output connector Filter 9 pole Elliptic and 5 pole Bessel filters Waveform Characteristics Harmonic Distortion (sine) DC-20 kHz, -65 dBc 20 kHz-100 kHz, 60 dBc 100 kHz-5 MHz, -45 dBc 5 MHz-50 MHz, -35 dBc Spurious (sine) DC-1 MHz < -65 dBc Rise/Fall Time (square, pulse) < 6 ns (10% to 90%) at full amplitude into 50 Q Variable Dut_y Cycle 20% to 80% to 10 MHz (square) 40% to 60% to 30 MHz (square) 50% >30 MHz (square) Variable Symmetry 10%-90% to 5 MHz (triangle) Symmetry at 50% < 0.5 % Linearity (triangle, ramp) <0.1% of peak output (1 jUHz to 250 kHz) Aberrations < 3 % of p-p amplitude ± 50 mV Pulse Width 20 ns to <(Period-20 ns) (10 ns resolution) Variable Edge Time 100 ns to Width/0.625 (50 % dut_y cycle) 10 ns resolution Operating Modes Continuous Output continuous at programmed parameters Triggered Output quiescent until triggered by an internal or external trigger, then one waveform cycle is generated to programmed parameters. Up to 20 MHz trigger rate for ARB waveforms and 10 MHz in DDS mode Gate Same as triggered mode, except waveform is executed for the duration of the gate signal. The last cycle started is completed Burst 2-999,999 cycles Phase -180 to +180 degrees with 0.1 degree resolution Trigger Source Trigger source may be internal, external or manual. Internal trigger rate 0.01 Hz-1 MHz (1 [Is - 100 s) Modulation Characteristics Amplitude Modulation Internal 0.01 Hz-20 kHz sine , square or triangle waveform variable modulation from 0% to 100% External 5 Vp-p for 100% modulation, 10 kQ input impedance, 0.01 Hz - 50 KHz bandwidth Frequency Modulation Internal 0.01 Hz-20 kHz sine wave, square or triangle External 5 Vp-p for 100% deviation, 10 kQ input impedance 0.01 Hz - 50 kHz bandwidth FSK Internal 0.01 Hz to 1 MHz External 1 MHz max. Sweep Characteristics Sweep Shape Linear and Logarithmic, up or down Sweep Time 10 ms to 500 s Sweep Trigger internal, external, continuous or burst Inputs and Outputs Trigger IN TTL Compatible Maximum rate 20 MHz Minimum width 20 ns Input Impedance10 kQ nominal Sync OUT TTL pulse at programmed frequency, 50 Q source impedance Modulation IN 5 Vp-p for 100% modulation 10 kQ input impedance DC to >50 kHz minimum bandwidth Marker Out Positive TTL pulse user programmable in Arbitrary waveform, 50 Q source impedance Reference IN-OUT 10 MHz, TTL compatible, input or output, for external unit synchronization 50 Q output impedance and 1 kQ input Summing IN 5 Vp-p signal for full scale output, 500 Q input impedance Internal Trigger Repetition 1 ms to 100 s Resolution 4 digits Accuracy ±0.002% General Display Resolution 160 x 80 dots LCD Remote Control Interface GPIB, RS-232 Store Memory 50 full panel settings at power-off Dimensions (WxHxD) 8.4(213) x 3.5(88) x 10.8(275) inches (mm) Weight Approx. 2.5 kg (5.55 lbs) Power 100-240 VAC ± 10%, 50 VA max. Temperature Operating 0 °C to + 50 °C Non-operating -20 °C to + 70 °C Humidity 95 % RH , 0 °C to 30 °C EMC According to EN5501 1 for radiated and conducted emissions Electrical Discharge Immunity According to EN55082 Safety Specifications According to EN61010 , CE approved Three Year Warranty Accessories Supplied: CD containing user manual & Wave-X software, null modem serial interface cable, power cord www.bkprecision.com