20 MHz Function / Arbitrary Generator - B&K Precision - #2

Text version of the page

Frequency Characteristics Sine 1ìHz ~ 20MHz 1ìHz ~ 80MHz Square 1ìHz ~ 20MHz 1ìHz ~ 40MHz All Other waveforms 1ìHz ~ 100kHz Frequency Stability ±1x10-6 (22°C ±5°C) Resolution 1ìHz Accuracy ± 5x10-6 (22°C ±5°C) Data entry Units s, ms, Hz, kHz, MHz Wave form Characteris tics Main Waveforms (Sine, Square) Amplitude resolution 12 bits Sample Rate 200MSa/s Sine Harmonic Distortion of - 50dBc (frequency 5MHz) Sine Wave* - 45dBc (frequency 10MHz) - 40dBc (frequency 20MHz) - 35dBc (frequency 40MHz) - 30dBc (frequency > 40MHz) THD* 0.1% (20Hz ~ 100kHz) Square Rise and fall time* 15ns * = Note: Test conditions for harmonic distortion, sine distortion, rise/fall time Output Amplitude 2Vp-p, Environmental temperature: 25°C±5°C Others built-in waveforms 27 build-in standard and Sine, Square, Triangle, Positive Ramp, Falling Ramp, complex waveforms Noise, Pulse, Positive Pulse, Negative Pulse, Positive DC, Negative DC, Stair wave, Coded Pulse, Full wave rectified, Half-wave rectified, Sine transverse cut, Sine vertical cut, Sine phase modulation, Logarithmic, Exponential, Half-round, Sinx/x, Square root, Tangent, Cardiac, Earthquake, Combination Waveform Length 4096 dots Amplitude Resolution 10 bits Pulse Duty Cycle 0.1% ~ 99.9% (below 10kHz), 1% ~ 99% (10kHz ~ 100kHz) Rise/Fall Time 100ns (Duty Cycle 20%) DC signal characteristics DC range 10mV – 10V (high impedance) DC Accuracy ±5% of setting +10mV (high impedance) Arbitrary Non volatile memory 8 waveforms Waveform length 8~16000 points Amplitude resolution 10 bits Frequency range 1ìHz~100kHz Sample rate 200MSa/s Amplitude Characteristics Amplitude Range (open circuit) Freq 40MHz: 2mV ~ 20Vpp , 1mV ~ 10Vpp (50Ù) Freq > 40MHz: 2mV ~ 4Vp-p, 1mV ~ 2Vpp (50Ù) Resolution 2ìVpp (open circuit), 1ìVpp (50Ù) Accuracy ± 1%+0.2mV (sine wave relative to 1kHz) Stability ±0.5 % /3 hours Flatness For amplitude 2Vpp ±3% (freq 5MHz), ±10% (5MHz2Vpp: ±5% (freq 5MHz), ±10% (5MHz20MHz) ±1dBm (frequency>40MHz) Output Impedance 50Ù Output Units Vpp, mVpp, Vrms, mVrms, dBm DC Offset Characteristics Offset Range (open circuit) Freq 40MHz): ±10Vpk ac+dc (Offset 2 x pk to pk amplitude) Freq >40MHz): ±2Vpk ac+dc (Offset 2 x pk to pk amplitude) Offset Resolution 2ìV (open circuit), 1ìV (50Ù) Offset Error ±5% of setting +10mV (Ampl. 2Vpp into open circuit) ±5% of setting +20mV (Ampl. > 2Vpp into open circuit) Modulation AM Characteristics Carrier Waveforms Sine or Square Modulation Source Internal or external Internal Modulating Waveform Sine, Square, Triangle, Rising/Falling Ramp Frequency of modulating signal 100ìHz ~ 20kHz Distortion 2% models 4084AWG 4086AWG Specifications Specifications (Cont.) Models 4084AWG & 4086AWG Modulation Depth 1% ~ 120%, 1% ~ 80% (frequency>40MHz, Ampl > 2Vpp into open circuit) Modulation Error ± 5%+0.2% (100ìHz < frequency 10kHz) ±10%+2% (10kHz < frequency 20kHz) Max. Amplitude of ext. input signal 3Vp-p (-1.5V~ +1.5V) FM Characteristics Carrier Waveforms Sine or Square Modulation Source Internal or external Internal Modulating Waveform Sine, Square, Triangle, Rising/Falling Ramp Frequency of modulating signal 100ìHz ~ 10kHz Deviation Max. 50% of carrier frequency for internal FM Max 100kHz (carrier frequency 5MHz) for external FM, with input signal voltage 3Vp-p (-1.5V~+1.5V) FSK Characteristics Carrier Waveform Sine or Square Control ModeI Internal or external trigger (external: TTL level, low level F1, high level F2) FSK Rate 0.1ms ~ 800s PSK Characteristics Carrier Waveform Sine or Square PSK Phase 1 (P1) and Phase 2 (P2), range: 0.0 ~ 360.0° Resolution 0.1° PSK rate 0.1ms ~ 800s Control Mode Internal or external trigger (external: TTL level, low level P1, high level P2) Burst Characteristics Waveform Sine or Square Burst Counts 1 ~ 10000 cycles Time interval between bursts 0.1ms ~ 800s Control Mode Internal, single or external gated trigger Frequency Sweep Characteristics Waveform Sine or Square Sweep Time 1ms ~ 800s (linear), 100ms ~ 800s (log) Sweep Mode Linear or Logarithmic Start/ Stop Frequency Same as frequency range of Sine & Square External trigger signal frequency DC ~ 1kHz (linear) DC~10Hz (log) Control Mode Internal or external trigger Inputs/ Outputs Main Output Impedance 50Ù Protection Short circuit and overload protected Output MOD OUT Frequency 100Hz ~ 20kHz Waveform Sine, Square, Triangle, Rising/Falling Ramp Amplitude 5Vp-p ± 5% Output Impedance 600Ù Modulation IN 3Vpp = 100% Modulation External Input Trig/FSK/Burst Level - TTL Univ ersal Counter, Key Specs* Frequency Range Frequency Measurement 1Hz ~ 100MHz Totalize mode 50MHz max * For the full specification of the counter section refer to www.bkprecision.com General Power Supply 198~242V or 99~121V, Frequency: 47~ 63Hz Power Consumption <35VA State Storage Memory Storage Parameters frequency, amplitude, waveform, DC offset values, modulation parameters Storage Capacity 10 user configurable stored states Dimensions (W x H x D) 10” x 3.93” x 14.56” (255 mm x 100 mm x 370 mm) Weight 6.6lbs (3 kg) Remote Interface RS232 Safety designed according to EN61010 EMC tested according to EN55022, EN55024, EN61326, EN601000 NOTE: Specifications and information are subject to change without notice. Please visit www.bkprecision.com for the most current product information. Accessories Included BNC to alligator cable, BNC to BNC cable, RS232 communication cable, power line cord, test report, spare fuse, software installation disk. Accessories One Year Warranty www.bkprecision.com Models 4084AWG & 4086AWG