You may also be interested in
Mass flow-meter, Indicator, Sensor, Turbine flow-meter, Differential pressure flow-meter
Text version of the page
Flow Rate Transitters Flow Rate TransittersTYPICAL PRESSRE IFFERENTIALSFor specific differential graphs,refer to Lake data sheet PDDS-404.MATERIALS OF CONSTRCTION ETTE COMPONENTSALUMINUMBRASSSTAINLESS STEEL High-pressure casing, Aluminum Brass 0 Stainless Steel end ports and tapered shaftSeals Buna-N STD, EPR,Buna-N STD, EPR,itonwith Teflonitonor alrezitonor alrezbackup STD, Buna-N, EPR or alrez Transfer MagnetTefloncoated AlnicoTefloncoated AlnicoTefloncoated Alnico Floating Orifice DiskStainless SteelStainless SteelStainless SteelAll other internal parts Stainless SteelStainless SteelStainless SteelTeflon is a registered trademark of DuPont de Nemours & Co.Viton and Kalrez are registered trademarks of Dow DuPont Elastomers. 0103050709011013015005101520 25 30 35 40 MATERIALS OF CONSTRCTION NON-ETTE COMPONENTSALUMINUMBRASSSTAINLESS STEEL Enclosure CoverAluminumAluminumAluminum SealsBuna-NBuna-NBuna-N WindowPyrexPyrexPyrexDin ConnectorPolyamidePolyamidePolyamidePyrex is a registered trademark of Corning Inc. MONITOR PERFORMANCEMeasuring accuracy: ±2.5% of full-scale in the center third of the measuring range; ±4% in upper and lower thirds Repeatability:±% of full-scale Flow measuring range:0.05-50 GPM 0.2-560 LPM; .5-00 SCFM 0.5-60 SLPS Maximum operating pressure: aluminum and brass monitors: 500 PSIG 240 Bar Stainless steel monitors: 6000 PSIG 40 Bar Maximum operating temperature:media: 240F 6C, ambient: 0F 2C010203040500510152025 Pressure differential:Liquid: see graphs. Gases: see Pneumatic data sheet Standard calibration media:Oil monitors: DTE 25 0F 4C, 0. sg Water monitors: tap water 0F 2C, .0 sg Air monitors: air 0F 2C, .0 sg and 00 PSIG 6. BarFiltration requirements:4 micron filter or 200 mesh screen minimum DTE 25 is a registered trademark of Exxon Mobil. ELECTRONIC TRANSMITTER PERFORMANCEPower requirements:2-5 dc Load driving capacity:4-20mA: Load resistance is dependent on power supply voltage. Use the following equation to calculate maximum load resistance: Max Loop Load 50Power supply volts – 2.0-5 DC: Minimum load resistance 000 . -5 DC: Minimum load resistance 25 Square Wave Pulse: Minimum load resistance 000 Transmission distance:4-20mA and -5 DC are limited only by wire resistance and power supply voltage. 200 feet recommended for 0-5 DC and square wave pulse. Over-current protection:self limiting at 5mA Resolution:0 bit 0.%0369121505101520 Isolation:Inherently isolated from the process Response time:00 milliseconds MECANICAL SIZE COEDIMSERIES SERIES 4SERIES SERIES A6-/6 6mm-5/2 2mm0-/ 25mm2-5/ 22mm B2-/6 56mm2-5/6 5mm-/6 mm-/6 mm C4 0mm4-/2 4mm5-5/6 5 mm5-5/6 5mmwww.lakemonitors.comD-/ 4mm-/ 4mm-/ 4mm-/ 4mm E4-/ 2mm5 2mm6-/4 2mm6-/4 2mmAW-LAE COMPANF2-/4 5mm2-/ mm-/4 5mm-/4 5mm Port SizesNPTF: /4, /, /2NPTF: /4, NPTF: -/4, -/2NPTF: 2SAE: 6, , 0SAE: 2, 6SAE: 20, 24SAE: 2 BSP:/, /2BSP: /4, BSP: -/4, -/2BSP: 2A TASI Group Company 0 Industrial Dr., Franksville,WI526262.4.00 / Fax: 262.4.000.50.60Note: Consult factory for SAE brass monitor requirements . RDS-1106 7.5M MR / WGD / MAS © 2006 AW-Lake oan |
|