cad

Vacuum Filter
12Pages

{{requestButtons}}

Catalog excerpts

Vacuum Filter - 1

ACCESSORIES GENERAL CATALOG AIR TREATMENT, AUXILIARY, VACUUM, AND FLUORORESIN PRODUCTS COMPACT FR SERIES CONTENTS Features Handling Instructions and Precautions Filters Specifications, Order Codes Flow Rate Characteristics, Dimensions Regulators Specifications, Order Codes Flow Rate Characteristics, Dimensions Filter Regulators Specifications, Order Codes Flow Rate Characteristics, Dimensions Manifold Regulators Specifications, Order Codes Flow Rate Characteristics, Dimensions Compact Pressure Gauge Before use, be sure to read the “Safety Precautions” AUTOMAX S.A. - Z.A. - Rue de Champ Chardon 41250 MONT PRES CHAMBORD - FRANCE E-mail: info@automax.fr www.automax.fr CAD drawing data catalog is availabl

Open the catalog to page 1
Vacuum Filter - 2

Compact and lightweight Air Filters, Regulators, and Filter/Regulators. A diaphragm is used in the regulator to provide good regulating performance. Conforms to non-grease specification.Note It is easy to install and use at airline ends. Fittings are supplied with the product as standard, making it easy to connect into applications. Standard products can be used as non-ion (NCU) specification products (excluding pressure gauge). For mounting the body, either select the special bracket or bolt mountings on the front of the body. Note:When assembling, a minimal amount of grease must be...

Open the catalog to page 2
Vacuum Filter - 3

Handling Instructions and Precautions n-HJ 1. While any mounting direction is acceptable, be careful to avoid directly applying strong shocks or vibrations to the body. 2. Pressure gauge connection port tightening torque Since the body is made of plastic, ensure that the tightening torque for the pressure gauge connection port (Rc1/8) remains within the figures shown below, and always use sealing tape. The recommended tightening torque for Rc1/8 fitting of 686~886N-cm [5.06~ 6.54ft-lb] will damage the body. MAX.150N-cm [13.3in-lb] When mounting the pressure gauge, always use a wrench on the...

Open the catalog to page 3
Vacuum Filter - 4

Air Filters for Pressure and Vacuum Special Purpose Filters for Vacuum and Vacuum Breaking Inner Construction Order Codes 100 - Mounting specification BlankA No bracket BA With bracket Fitting specification J4 4mm [0.157in.] J6 6mm [0.236in.] J1/8A 1/8in. tube J1/4A 1/4in. tube FN A Air filters for pressure and vacuum VFNA Special purpose filters for vacuum and vacuum breaking #Order code for bracket only B-RN100 Item Model

Open the catalog to page 4
Vacuum Filter - 5

FN100-J6, J1/4 pressure Ugeqpf ct{ "r tguuw tg

Open the catalog to page 5
Vacuum Filter - 6

Specifications ^Relief specifications ^Non-relief specifications Remark: The regulator of the Compact FR Series operates in the same way as the type with built-in check mechanism. When the regulator’s primary pressure is discharged, the secondary pressure is discharged to the primary side. However, if the secondary pressure has been pressurized by an air cylinder, etc., to a pressure higher than the set pressure, discharging the secondary pressure may become difficult. Order Codes •Side piping regulator Mounting specification BlankA No bracket (no mounting ring) B A With bracket (no...

Open the catalog to page 6
Vacuum Filter - 7

1MPa = 145psi. 1R /min = 0.0353ft.3/min. Remark: Graphs show the flow rate when the primary pressure is constant at 0.7MPa [102psi.]. Pressure Characteristics Flow Rate Characteristics Side piping regulator Bottom piping regulator Note: The required mounting hole when the regulator

Open the catalog to page 7
Vacuum Filter - 8

Model Item •Relief specification •Non-relief specification Mounting specification BlankA No bracket (no mounting ring) B A With bracket (no mounting ring) R A With mounting ring (no bracket) Pressure gauge specification BlankA No pressure gauge GD18A With pressure gauge Pressure and relief specification 100A 0.7MPa [102psi.] relief specification 101A 0.25MPa [36psi.] relief specification 110A 0.7MPa [102psi.] non-relief specification 111A 0.25MPa [36psi.] non-relief specification •Order code for bracket only B-RN100 •Order code for mounting ring only •Order code for pressure gauge only

Open the catalog to page 8
Vacuum Filter - 9

Flow Rate Characteristics 1MPa = 145psi. 1R /min = 0.0353ft.3/min. Remark: Graphs show the flow rate when the primary pressure is constant at 0.7MPa [102psi.]. Dimensions of Filter Regulators (mm) Frn100 Note: The required mounting hole when the regulator is installed to a pane

Open the catalog to page 9
Vacuum Filter - 10

Symbols Specifications •Relief specification Pressure gauge Pressure gauge connection port connection port •Non-relief specification Pressure gauge Pressure gauge connection port connection port Model Item Remark: The basic inner construction and major parts materials are the same as for RDN. See p.107. Order Codes Mass station. H When using a block-off plate for closing, enter BP. •Manifold regulator single unit Pressure gauge specification BlankA No pressure gauge GD18A With pressure gauge Order code for block-off plate only Fitting specification (one block-off plate, two...

Open the catalog to page 10
Vacuum Filter - 11

Pressure Characteristics 1MPa = 145psi. 1R / min = 0.0353ft.3/min. Remark: Graphs show the flow rate when the primary pressure is constant at 0.7MPa [102psi.]. Qsjn bsz!qsf ttvsf NQb Dimensions of Manifold Regulators (mm) •Manifold regulator single unit Mrn100

Open the catalog to page 11
Vacuum Filter - 12

Order Code Dimensions of Compact Pressure Gauge (mm)

Open the catalog to page 12

All AUTOMAX catalogs and technical brochures

  1. Vacuum Valve

    28 Pages

  2. Flow sensor

    36 Pages