FM Application Notes - Aurel - #9

/ 21


catalogue search
P. 01
P. 02
P. 03
P. 04
P. 05
P. 06
P. 07
P. 08
P. 09
P. 10
P. 11
P. 12
P. 13
P. 14
P. 15
P. 16
P. 17
P. 18
P. 19
P. 20
P. 21
Pages:


See other catalogues for Aurel

Text version of the page
Mod. TX-DFM-XX
Application note • Nota applicativa
PIN OUT
1-Power Supply.
2-Tx Enable. If set to a positive voltage (3^5V) this pin enables supply to the complete circuit system, comprehensive of Aux Out pin; if set to a low voltage (max 0.5V), it forces the complete transmitter shut-off at zero current consumption. When enabled, the system irradiates the carrier at nominal frequency (433.65 Mhz) if Data Input pin is at 0V (max 0.5V) or at a shifted higher frequency (about+150 Khz from carrier) if Data Input pin is set at 3^5V. A maximum delay time of 500 usec should be allowed from enabling time to the first digital data line state exchange (from 0 to 1 or from 1 to 0). 3-Ground.
4-Data input. If at low voltage (max 0.5V), the carrier irradiates at the nominal frequency value (433.65 Mhz); if voltage at this pin is high, the frequency deviates to a +150 Khz nominal higher value. Max. Modulation frequency is 10 Khz at square wave. The system works with direct modulation, so it has no low limit in the modulation frequency band it can handle, performing at best also at 0 Hz.
5-Aux Out. Auxiliary supply output pin: voltage will be
present when Tx is enabled. This pin is available to feed
ancillary small devices under the same transmitter enabling
control line.Maxavailable current is 10 mA.
9-Ground.
13-Ground.
15-RF Output. RF power available is less than 10mW on a 50
ohm load.
16-Ground.
PIN OUT
l-Power Supply.
2-Tx Enable. Se a tensione positiva (3+5V), consente l'alimentazione dell'intero sistema compreso ilpin Aux Out; se a tensione nulla (max 0,5V), consente il totale spegnimento del trasmettitore con conseguente consumo nullo. Il sistema, quando viene abilitato, trasmette la portante a frequenza nominale (433,65Mhz) se ilpinData Input e' a 0V (max 0,5V) e ad una frequenza spostata in alto di circa +150 Khz se il pin Data Input e' a 3^5V : č richiesta una attesa massima di 500 fisec dall' istante di abilitazione prima di poter commutare il dato da 0 a l o da l a 0. 3-Ground.
4-Data input. Se basso (max 0,5V), la portante rimane al valore della frequenza nominale (433,65 Mhz); se alto (3+5V), la frequenza della portante aumenta della deviazione nominale +150 Khz. La massima frequenza di modulazione e' 10 Khz in onda quadra. Il sistema e a modulazione diretta e pertanto non ha limite minimo di frequenza di modulazione, accettando anche 0 Hz.
5-Aux Out. Tensione di alimentazione ausiliaria presente
quando il Tx e' abilitato. Consente di alimentare dispositivi che
si vuole non assorbano quando il sistema e disabilitato: 10 mA
max disponibili.
9-Ground.
13-Ground.
15-RF Output. Disponibile una potenza RF inferiore a 10mW
su carico da 50 ohm.
16-Ground.
START-UP SEQUENCE
SEQUENZA di ACCENSIONE
.TX-ENABLE
OV 1
MAX 500 LLsec
i DATA IN
UNCERTAINTY PERIOD
START BIT
-►?*- -
MAX 500 usee 500 usee (See NOTE)
kRF (Mhz)
MAX 500 usee 500 usee (See NOTE)
This information may be subject to revision without notice. AUR°EL makes no warranty and assumes no liability in connection with any use of this information . Variazioni senza preavviso delle presenti informazioni non implicano responsabilitā da parte AUR°EL. L'acquirente assume ogni responsabilitā derivante dall'uso del prodotto.
2-3

pageCatalog pdf di En 2012-05-21-27