Text version of the page

SPECTRUMANALYZERS

?

Option 04: High-speed time domain sweep

?

Option 07: AM/FM demodulator

12.5 µs, 25 µs, 50 µs, 100 to 900 µs (one most Sweep timesignificant digit settable) 1.0 to 19 ms (two upper significant digits settable) Voice outputWith internal loudspeaker and earphone connector (ø3.5 jack), adjustable volume Accuracy±1%
1 Marker level 0.1 dB (log scale), 0.2% (linear scale, relative to resolutionreference level)

?

Option 10: Centronics interface*

FunctionOutputs data to printer (Centronics standard)

∗

This option is recommended to be mounted together with option 06. ConnectorD-sub 25-pin (jack)

∗

1: GPIB interface cannot be installed simultaneously.

?

Option 06: Trigger/gate circuit

Trigger switchFREERUN, TRIGGERED Trigger level: ±10 V (resolution: 0.1 V), TTL level EXTTrigger slope: Rise/Fall Connector: BNC Log scale: –100 to 0 dB (resolution: 1 dB) VIDEOTrigger slope: Rise/Fall Trigger level: High, middle, or low selectableWIDE IF VIDEOBandwidth: ≥ 20 MHzTrigger slope: Rise/Fall LINEFrequency: 47.5 to 63 Hz (line lock)
Trigger source Method: M-NTSC, B/G/H PAL Sync: V-SYNC, H-SYNC Sync line (NTSC)TVH-SYNC (ODD): 7 to 262 line, H-SYNC (EVEN): 1 to 263 lineSync line (PAL)H-SYNC (ODD): 1 to 312 line, H-SYNC (EVEN): 317 to 625 line

∗

Option 16 required Pre-trigger (displays waveform from previous max. 1 screen at trigger occurrence point) Range:–time span to 0 s Trigger delayResolution: time span/500Post trigger (displays waveform from after max. 65.5 ms at trigger occurrence point)Range: 0 to 65.5 ms Resolution: 1 ms In frequency domain, displays spectrum of input signal in specified gate interval Gate sweepGate delay: 0 to 65.5 ms (from trigger point, resolution: 1 µs)Gate width: 2 µs to 65.5 ms (from gate delay, resolution: 1 µs)

?

Option 08: Pre-amplifier*

1,

*

2 Frequency range100 kHz to 3 GHz Noise figure ≤ 8 dB (typical, <2 GHz), ≤ 13 dB (typical, ≥ 2 GHz) Measurement rangeAverage noise level to +10 dBm Max. input levelCW average power: +10 dBm, ±0 Vdc Average noise level ≤ –132 dBm (1 MHz to 1 GHz), ≤ –132 dBm + 2f [GHz] dB (>1 GHz)

∗

RBW: 1 kHz, VBW: 1 Hz, RF ATT: 0 dB Setting rangeLog scale: –120 to +10 dBm, or equivalent level Linear scale: 22.4 µV to 707 mVReference level accuracy: ±0.5 dB (–69.9 to –20 dBm), ±0.75 dB (–89.9 to –70 dBm, –19.9 to +10 dBm)Reference level

∗

After calibration, referenced to 100 MHz, 1 MHz span (RF ATT, RBW, VBW and sweep time set to AUTO) RBW switching uncertainty: ±0.5 dB

∗

After calibration, referenced to 3 kHz RBWRF ATT switching uncertainty:±0.5 dB (0 to 50 dB), ±1.0 dB (0 to 70 dB)
Amplitude

∗

After calibration, referenced to 100 MHz, RF ATT: 10 dB Frequency response±2.0 dB (100 kHz to 3 GHz, referenced to 100 MHz, RF ATT: 10 to 50 dB) Linearity of waveform Log scale (after calibration): ±0.5 dB (0 to –20 dB), ±1.0 dB (0 to –60 dB), ±1.5 dB (0 to –75 dB) displayLinear scale (after calibration): ±5% (according to reference level) Two signals 3rd order intermodulation distortion: ≤ –70 dBc (10 MHz to 3 GHz)Spurious response

∗

Frequency difference of two signals: ≥ 50 kHz, Pre-amplifier input
∗ 3 :–55 dBm 1 dB gain compression ≥ –35 dBm ( ≥ 100 MHz, at pre-amplifier input level
∗ 3 )

∗

1: Overall specification with pre-amplifier on (Noise figure is the simple performance)

∗

2: Option 20 cannot be installed simultaneously

∗

3: Pre-amplifier input level = RF input level – RF ATT setting level

http://www.anritsu.com 478