Text version of the page

SPECTRUMANALYZERS

Frequency range: 18 to 110 GHzFrequency band configurationFrequency Band K: 18 to 26.5 GHz (n: 4), Band A: 26.5 to 40 GHz (n: 6), Band Q: 33 to 50 GHz (n: 8), Band U: 40 to 60 GHz (n: 9),Band V: 50 to 75 GHz (n: 11), Band E: 60 to 90 GHz (n: 13), Band W: 75 to 110 GHz (n: 16) Span setting range: 0 Hz, (100 x n) Hz to each bandwidth

∗

n: harmonic order of the mixer Level measurement Mixer conversion loss setting range: 15 to 85 dBAmplitudeMaximum input level: Depends on the external mixer used Average noise level: Depends on the external mixer used Reference level setting range: –100 dBm to (–25 to M) dBm
External mixerOthers

∗

Log scale, M: mixer conversion loss Frequency response: Depends on the external mixer used Input/outputSuitable mixer: 2-port mixer only (local frequency: 4 to 7 GHz, IF frequency: 689.31 MHz)Display gain: 0 ±2 dB (external mixer input: –10 dBm, when the mixer conversion loss is 15 dB) EN61326: 1997/A2: 2001 (Class A)EMCEN61000-3-2: 2000 (Class A)EN61326: 1997/A2: 2001 (Annex A) LVDEN61010-1: 2001 (Pollution Degree 2) Vibration Meets the MIL-STD-810D Power (operating range)85 to 132/170 to 250 Vac (automatic voltage switching), 47.5 to 63 Hz, ≤ 400 VA Dimensions and mass 320 (W) x 177 (H) x 381 (D) mm, ≤ 15 kg (without option) Ambient temperature 0 to +50ËšC (operate), –40 to +75ËšC (storage)

?

Option 02: Narrow resolution bandwidth

?

Option 06: Trigger/gate circuit

Resolutionbandwidth (3 dB)30 Hz, 100 Hz, 300 Hz Trigger switchFREERUN, TRIGGERED EXTTrigger level: ±10 V (resolution: 0.1 V), TTL level Trigger slope: Rise/fall Connector: BNCVIDEOLog scale: –100 to 0 dB (resolution: 1 dB) Trigger sourceTrigger slope: Rise/fall WIDE IF VIDEO Trigger level: High, middle, or low selectable Bandwidth: Resolution bandwidthswitching uncertainty ±0.4 dB (RBW 3 kHz referenced) Resolution bandwidth accuracy ±20% ≥ 20 MHz Trigger slope: Rise/fall LINEFrequency: 47.5 to 63 Hz (line lock) Selectivity (60 dB:3 dB) ≤ 15:1

?

Option 03: Narrow resolution bandwidth

Resolution10 Hz, 30 Hz, 100 Hz, 300 Hzbandwidth (3 dB) Resolution bandwidth Pre-trigger (displays waveform from previous max. 1 screen at trigger occurrence point) switching uncertainty ±0.4 dB (RBW 3 kHz referenced) Trigger delayPost trigger (displays waveform from after max. 65.5 ms at trigger occurrence point) Range: 0 to 65.5 ms, Resolution: 1 µs Range:–time span to 0 s, Resolution: time span/500 Resolution bandwidth accuracy ±20% Selectivity(60 dB:3 dB) ≤ 15:1 In frequency domain, displays spectrum of input signal in specified gate intervalGate sweepGate delay: 0 to 65.5 ms (from trigger point, resolution: 1 µs)Gate width: 2 µs to 65.5 ms (from gate delay, resolution: 1 µs) ≤ –135 dBm (1 MHz to 1 GHz, band 0), ≤ –135 dBm + 1.5f [GHz] dB (1 to 3.1 GHz, band 0), ≤ –130 dBm (3.1 to 8.1 GHz, band 1), Average noise level ≤ –122 dBm (8.0 to 15.3 GHz, band 2), ≤ –118 dBm (15.2 to 22.4 GHz, band 3), ≤ –111 dBm (22.3 to 30 GHz, band 4)

∗

RBW: 10 Hz, VBW: 1 Hz, RF ATT: 0 dB

?

Option 07: AM/FM demodulator

?

Option 04: High-speed time domain sweep

Voice outputWith internal loudspeaker and earphone connector (ø3.5 jack), adjustable volume 12.5 µs, 25 µs, 50 µs, 100 to 900 µs (one most Sweep timesignificant digit settable)1.0 to 19 ms (two upper significant digits settable)

?

Option 10: Centronics interface*

1 Accuracy±1% FunctionOutputs data to printer (Centronics standard) Marker level Log scale: 0.1 dB, Linear scale: 0.2% (relative to resolutionreference level) Connector D-sub 25-pin (jack)

∗

1: GPIB interface can not be installed simultaneously.Sweep output (X)0 to 10 V ±1 V (

∗

This option is recommended to be mounted together with option 06.

?

Option 15: Sweep signal output

≥ 100 k Ω termination, from left side to right side of display scale), BNC connector Sweep status output (Z)TTL level (low level with sweeping), BNC connector

http://www.anritsu.com 468