Text version of the page

SPECTRUMANALYZERS

Option 03: Extension of pre-selector lower limit to 1.6 GHz

FunctionExtends the lowest frequency of pre-selector from 3.15 to 1.6 GHz Frequency band0 band: 9 kHz to 3.2 GHz, 1–L band: 1.6 to 3.2 GHz, 1– band: 3.15 to 6.3 GHz, 1+ band: 6.2 to 7.8 GHz Pre-selector range1.6 to 7.8 GHz (band: 1–L, 1–, 1+) Average noise level ≤ –122 dBm + 0.5f [GHz] dB (1.6 to 7.8 GHz, band 1, RBW: 300 Hz, VBW: 1 Hz, RF ATT: 0 dB) Residual response ≤ –90 dBm (1.6 to 7.8 GHz, band 1, RF ATT: 0 dB, input terminated at 50 Ω )±1.0 dB (with 1.6 to 7.8 GHz, band 1, and 50 MHz referenced, when RF ATT is 10 dB and temperature is +18 to +28ËšC)Frequency response±2.0 dB (1.6 to 7.8 GHz, band 1, RF ATT: 10 dB to 62 dB)

∗

After pre-selector tuning for band 1 2nd harmonic distortion ≤ –90 dBc (0.8 to 3.9 GHz, band 1, mixer input: –10 dBm) 1 dB gain compression ≥ 0 dBm (1.6 to 7.8 GHz, band 1)Maximum dynamic range ≥ –122 dB + 0.5f [GHz] dB (1.6 to 7.8 GHz, band 1)

Option 04: Digital resolution bandwidth

Setting range: 10 Hz to 1 MHz (1, 3 sequence)Bandwidth accuracy: ±10% (RBW: ≥ 100 Hz), ±10% NOMINAL (RBW: ≥ 30 Hz)Resolution bandwidthBandwidth selectivity (60 dB: 3 dB): ≤ 5:1 (RBW: ≥ 100 Hz), ≤ 5:1 NOMINAL (RBW: ≤ 30 Hz) RBW switching uncertainty: 0.5 dB Span settingMinimum span setting: 1 kHzDetection modeNORMAL, POSITIVE PEAK, NEGATIVE PEAK, SAMPLE, RMS RMS: displays root-mean-square value of average power between sample points When RBW is 10 Hz and RF ATT is 0 dB[Without Option 08] ≤ –136.5 dBm + f [GHz] dB Typical (1 MHz to 2.5 GHz, band 0) ≤ –132.5 dBm + f [GHz] dB Typical (2.5 to 3.2 GHz, band 0)Average noise level

6

≤ –134.5 dBm + 0.5f [GHz] dB Typical (3.15 to 7.8 GHz, band 1)[With Option 08] ≤ –134.5 dBm + 1.5 x f [GHz] dB Typical (1 MHz to 2.5 GHz, band 0) ≤ –130.5 dBm + 1.5 x f [GHz] dB Typical (2.5 to 3.2 GHz, band 0) ≤ –134.5 dBm + 0.5 x f [GHz] dB Typical (3.15 to 7.8 GHz, band 1)

Option 08: Pre-amplifier

∗ 1 Frequency range100 kHz to 3 GHz Gain20 dB Typical Noise figure6.5 dB Typical (input frequency ≤ 2 GHz), 12 dB Typical (input frequency >2 GHz) Level measurement rangeAverage noise level display to +10 dBm Max. input levelCW average power: +10 dBmSetting rangeLog scale: –120 to +10 dBm, or equivalent, Linear scale: 2.24 µV to 707 mVReference level accuracy: ±0.9 dB (–69.9 to +10 dBm), ±1.5 dB (–90 to –70 dBm)Reference level

∗

After calibration, with 50 MHz referenced, 1 MHz span (RF, RBW, VBW, and sweep time set to AUTO)RBW switching uncertainty: ±0.5 dB (300 Hz to 5 MHz), ±0.75 dB (10 MHz, 20 MHz) RF ATT switching uncertainty: ±0.5 dB (10 to 50 dB), ±0.75 dB (52 to 62 dB)

∗

With 50 MHz referenced, when RF ATT is 10 dB Average noise level display–137 dBm + 2.0 x f [GHz] dB (1 MHz to 2.5 GHz, band 0)

∗

When RBW is 300 Hz, VBW is 1 Hz, RF ATT is 0 dB, and detection mode set to SAMPLEFrequency response±2.0 dB (100 kHz to 3.0 GHz)

∗

With 50 MHz referenced, when RF ATT is 10 dB to 50 dB, and temperature is +18 to +28ËšCLog scale (after calibration): Linearity of waveform display±0.5 dB (0 to –20 dB, RBW: ≤ 1 kHz), ±1.0 dB (0 to –60 dB, RBW: ≤ 1 kHz), ±1.5 dB (0 to –75 dB, RBW: ≤ 1 kHz) Linear scale (after calibration): ±5% (relative to reference level)Spurious response ≤ –70 dBc (10 MHz to 3 GHz)

∗

Frequency difference of two signals ≥ 50 kHz, At pre-amplifier input level of –55 dBm
∗ 2 1 dB gain compression ≥ –35 dBm (input frequency ≥ 100 MHz)

∗

At pre-amplifier input level

∗

1 : Overall specification with pre-amplifier ON (Noise figure and gain are single performance of pre-amplifier.)

∗

2 : Pre-amplifier input level is shown by the following equation: Pre-amplifier input level = RF input level – RF ATT setting level

Option 09: Ethernet interface Option 18: I/Q unbalanced input

FunctionExercises control with external controller (except for power ConnectorBNC switch)Connector10base-T Impedance Selectable between 1 M Ω (parallel capacity <100 pF) and 50 Ω Input level Differential voltage range: 0.1 Vp-p to 1 Vp-p (at input terminal) rangeChangeable between DC connection and AC connection

Option 17: I/Q balanced input

ConnectorBNC

Option 34: 4 GHz LO output

Impedance Selectable between 1 M Ω (parallel capacity <100 pF) and 50 Ω Frequency: 4 GHzFrequencyFrequency accuracy: Input level Differential voltage range: 0.1 Vp-p to 1 Vp-p (at input terminal) rangeIn-phase voltage range: ±2.5 V (at input terminal) ±(4 GHz x reference frequency accuracy) ±1 Hz Output level–10 dBm TypicalSpurious ≤ –40 dBc Typical

http://www.anritsu.com 455