S116 Safety Products Catalog
740Pages

Ensign > 3Pre-bored Shaft MSR57P Safety Relays Hinge Switches Page 5-54 Page 3-94 CompactBlock SensaGuard > ٙ Safety Relays Non-Contact Switches Page 5-30 PowerFlex Page 3-56 Grip Switch Enabling Switches Emergency Stop Devices 4-20MSR144RTP MSR300 > 4Stainless Steel Safety Relays Page 5-92 Emergency StopDevices Page 4-16 > ٙ Multizone Opto-electronics > Safety Contractors& Control Relays Page 2-71 Motor Control Centers Page 6-16Safety Control Relays Page 6-43SafeZone ArmorBlock > ٮ Guard I/O > ٮ ProgrammableSafety Solutions > 7000 Safety Drives Page 5-135 Lifeline Safety Motion Page 6-2...

Table of Contents General > Safety Guidelines and Metric Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Terms and Conditions of Sale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

ATTENTION: As the installer of this control system, you must be knowledgeable of otherapplicable standards pertaining to safety recommendations related to: Machine Construction General Electrical Machine Guarding Point of Operation guards, safety light curtains, mechanical guards, and two-handcontrols, and safety monitoring relaysIn addition to local laws and codes, you are responsible for the safety recommendationsdetailed in all applicable national and international codes and standards including: National Electric Code National Regulations Implementing European Directives OSHA Regulations...

Metric Conversion FactorsFromToMultiply by > Inches (in)Millimeters (mm)25.4Inches (in)Centimeters (cm)25.4Feet (ft)Meters (m)0.305Yards (yd)Meters (m)0.914Millimeters (mm)Inches (in)0.0394Centimeters (cm)Inches (in)0.394Meters (m)Feet (ft)3.28 Meters (m)Yards (yd)1.09Square inches (in > General 2 )Square millimeters(mm > 2 )645.0Square inches (in > 2 )Square centimeters(cm > 2 )6.45Square feet (ft > 2 )Square meters (m > 2 )0.0929Square yards (yd > 2 )Square meters (m > 2 )0.836Square millimeters(mm > 2 2 )Square inches (in )0.00155Square centimeters(cm > 12345 2 2 )Square inches (in...

Untitled table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:6.00pt "Arial", sans-serif; } .font1 { font:7.00pt "Arial", sans-serif; } .font2 { font:9.00pt "Arial", sans-serif; } .font3 { font:13.00pt "Arial", sans-serif; } .font4 { font:14.00pt "Arial", sans-serif; } Ternis and Conditions of Sale These gnral terms and conditions of sale only apply to direct sales by the manufacturer or its affiliates. Sales by appointed distributors and other independent authorized resellers will be subject to terms and conditions of sale and may be separately established by each...

Government Clauses and Contracts No government contractregulations or clauses will apply to the Products or this agreement or act to bind Seller unless specifically agreed to by Seller in writing at Sellerגs headquarters. Products sold or licensed hereunder are not intended to be used, nor should they be used, in any nuclear- related application either as a "Basic Component" under 10 CFR 21 (United States NRC) or otherwise under similar nuclear laws and regulations of this or any other country. Force Majeure Seller will not be liable for any loss, damage ordelay arising out of its failure...

Assignment Language The parties acknowledge that they have required thatthis agreement be drawn up in English. Les parties reconnaissent avoir exigש la rdaction en anglais du Contrat. In the event of a conflict between the English and other language versions of this agreement, the English version will prevail. This agreement may not be assigned by either partywithout the written consent of the other, however, consent will not be required for internal transfers and assignments as between Seller and its parent corporations, subsidiaries or affiliates as part of a consolidation, merger or...

Untitled table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:6.00pt "Arial", sans-serif; } .font1 { font:7.00pt "Arial", sans-serif; } .font2 { font:8.00pt "Arial", sans-serif; } .font3 { font:9.00pt "Arial", sans-serif; } .font4 { font:13.00pt "Arial", sans-serif; } .font5 { font:14.00pt "Arial", sans-serif; } Maintenance of Industrial Control Equipment ATTENTION:: Servicing energized Industrial Control Equipment can be hazardous. Severe injury or death can result from electrical shock, burn, or unintended actuation of controlled equipment. Recommended practice...

Replacements Final Check Out Use only replacement parts and devicesrecommended by Allen-Bradley to maintain the integrity of the equipment. Make sure the parts are properly matched to the model, series and revision level of the equipment. For additional information, refer to NEMA ICS 1.3, PREVENTIVEMAINTENANCE OF INDUSTRIAL CONTROL AND SYSTEMS EQUIPMENT, published by the National Electrical Manufacturers Association, and NFPA70B, ELECTRICAL EQUIPMENT MAINTENANCE, published by the National Fire Protection Association. חAfter maintenance or repair of industrial controls,always test the...

First Numeral Second Numeral IEC Publication 60259 describes standard Degrees of Protectionthat enclosures of a product are designed to provide when properly installed. > Protection of persons against accessto hazardous parts and protectionagainst penetration of solid foreignobjects.Protection against ingress of waterunder test conditions specified in IEC60259.0 Non-protected0 Non-protected1 Back of hand; objects greater than50mm in diameter2 Vertically falling drops of water3 Finger; objects greater than12.5mm in diameter4 Vertically falling drops of water withenclosure tilted 155 Tools or...