UKAN - Fine Screw Coupling Connectors - AB Connectors - (Version JPG) - Page n° 29 - PDF Catalogue | Technical Documentation

Connectors

CIRCULAR CONNECTORS

UK-AM

Page 27 of 52

Contacts


CABLE CONDUCTOR		CONTACTS
Stranding	Area (square	Size	Part Numbers*		Identification
	inches)
19/0.0076"	Q.O0Q86	16/20	Plug Pin Socket Insert	508/2/05604 508/1/056Q2	Two Grooves
23/0.0076'^J 33/0.0076"	0.001 0.0015	16/18	Plug Pin Socket Insert	508/2/05603 508/1/05601	One Groove
40/0.0076"	o.oo ia	16	Plug Pin Socket Insert	508/2/03547 508/1/04585 .	Nil
70/0.0076"	0.0032	12/14	Plug Ptn Socket Insert	508/2/09361 508/1/09374 ■	One Groove
110/0.0076"	.0.0050	12	Plug Pin Socket insert	508/2/09360 508/V09373	Nil
73/0 _012"	0.00S3	8/10	Plug Pin Socket Insert	508/2/00409 508/1/00407	One Groove
120/0.012"	0 0136	8	Plug Pin Socket Insert	508/2/09363 508/1/09376	Nil
1S2/0.012"	0.206	«1/6	Plug Pin Socket Insert	508/2/00406 508/1/00404	One G roove
294/Q.Q12"	0.0335	4	Plug Pin Socket Insert	508/2/09364 508/1/09377	Nil

i-CHHDO =

Size 16/20

Bore 0.042/0.044"

Bore 0.053/0.055" Bore 0.0615/0.0635' Bore 0.0615/0.0635'

Bore 0.078/0.080" Bore 0.096/0.098" Bore 0.126/0.130" Bore 0.167/0.171" BoreO.216/0.220"

Bore 0.279/0,283"

Size 16/18

Size 12/16

Size 12/14 Size 1 2

=№№

Size 8/10

_Size 4/6

□an

* Add /001 for gold plated or /002 for silver plated.

Size 4

Experience gained over many years has proved that contacts carefully machined from the finest quality brass, and silver or gold plated are ideally suited for the conditions encountered in normal usage; the advanced design of the socket insert with the internal spring and solid ring entry has proved to be without parallel in its field, ensuring perfect contact and low resistance to the flow of current with minimum voltage drop.

The range of contacts for the U K-AN connector has also been designed to allow a crimped joint on a wide range of cables without the use of sleeves. Both the size 15 and size 12 contacts are available with three different sizes of conductor well to accommodate the smaller cables, and to facilitate identification, a series of grooves is machined at the conductor well end. Details of the whole range of contacts are given above together with dimensions of cables to which a crimped connection may safely be made.

Selection of contacts

In view of the variations of contacts whtch are available, it is not possible to supply any connector complete with contacts under one part number.

Therefore it is essentia! that ail contacts are specified separately when ordering UK-AN connectors.

Selection of suitable contacts must be governed by (a) the si2e of the contact as defined by the contact arrangement and [b] the dimensions of the conductor of the cable to be used.

Although the following table gives details of a variety of cables which may be crimped, any other cable of similar conductor area and diameter may also be used. The use of size 16 square form crimping dies allows the small equipment wires to be crimped without doubling the conductor. Square form crimping dies should always be used for crimping cables with nickel plated conductors or where connectors are used at temperatures above +150^CC,

UKAN - Fine Screw Coupling Connectors - AB Connectors - #29

High density connector, Bayonet connector, Connector, Miniature connector, Circular connector